To Next PageTo Next Page
Need help?Do you have a question about the Cisco Nexus 5600 Series and is the answer not in the manual?
General| Switching Capacity | Up to 2.56 Tbps |
|---|---|
| Operating System | Cisco NX-OS |
| Software | NX-OS Software |
| Virtualization | Yes |
| QoS Support | Yes |
| Series | Nexus 5600 |
| Product Series | Nexus 5600 |
| Category | Switch |
| Switch Type | Data center |
| Form Factor | Fixed |
| Forwarding Rate | Up to 1440 Mpps |
| Port Speed | 10 Gigabit Ethernet, 40 Gigabit Ethernet |
| Power Supply | Redundant power supplies |
| Fans | Redundant fans |
| Management | CLI, SNMP, XML API |
| Layer Support | Layer 2, Layer 3 |
| VLAN Support | Yes |
| Security Features | ACLs, Port Security, DHCP Snooping, IP Source Guard |
| Redundancy | Redundant power supplies and fans |
| Dimensions | 1.72 x 17.3 x 22.5 in (4.37 x 43.94 x 57.15 cm) |
Describes the intended audience for this publication.
Explains the formatting and conventions used in command descriptions.
Lists URLs for related Cisco Nexus documentation.
Clears multicast routes based on specified criteria like group, source tree, or VRF.
Configures the maximum number of entries allowed in the multicast routing table.
Configures a Layer 3 Ethernet IEEE 802.3 routed interface.
Configures multicast reverse path forwarding (RPF) static routes.
Configures an Ethernet interface as a Layer 3 routed interface.
Displays information about IGMP snooping status and configuration.
Displays information about IPv4 Protocol Independent Multicast (PIM) routes.
Displays information about IPv6 multicast routes in the routing table.
Displays information about IPv4 multicast routes.
Clears specific IGMP event history buffers such as CLI, errors, or HA.
Enables a route-map policy to control multicast group joins for hosts.
Translates IGMPv1/v2 membership reports to create (S,G) state for IGMPv3.
Clears information from IGMP snooping event history buffers for specific types.
Configures the maximum number of groups learned through IGMP Snooping.
Enables or disables IGMP snooping for the current virtual device configuration (VDC).
Enables or disables IGMP snooping on specified VLAN interfaces.
Clears TCP connections to Multicast Source Discovery Protocol (MSDP) peers.
Enables or disables the Multicast Source Discovery Protocol (MSDP) feature.
Configures an MSDP peer with a specified IP address and connection source.
Configures the peer keepalive interval and timeout for MSDP sessions.
Restarts the Multicast Source Discovery Protocol (MSDP) process.
Displays information about Multicast Source Discovery Protocol (MSDP) peers.
Clears multicast routes from the IPv4 multicast routing table.
Clears information from IPv4 PIM event history buffers.
Enables or disables the Protocol Independent Multicast (PIM) feature.
Sets the maximum number of entries in the multicast routing table.
Configures an IPv4 PIM Anycast-RP peer for a specified Anycast-RP address.
Enables IPv4 Protocol Independent Multicast (PIM) sparse mode on an interface.
Enables IPv6 Protocol Independent Multicast (PIM6) sparse mode on an interface.
Restarts the IPv4 Protocol Independent Multicast (PIM) process.
Restarts the IPv6 Protocol Independent Multicast (PIM6) process.
Displays information about IPv4 Protocol Independent Multicast (PIM) rendezvous points (RPs).
Displays information about IPv6 Protocol Independent Multicast (PIM6) rendezvous points (RPs).
