Page 48
keypad.
Option 6 Receiver Fail Beeps Keypad Buzzer - If this option is on a Receiver Failure will cause the keypad
buzzer to sound continuously. The continuous beep will automatically clear when the Receiver starts to
see transmissions again or it can be silenced by pressing the <ENTER> button on the keypad.
Option 7 Turn Off Keypad LED’s and Backlighting when Armed - This option allows the LED’s and all
backlighting on a keypad to be turned off when the panel is in the Armed state. It is normally used to cut
the illumination from a keypad at night time. The LED’s and backlighting will return to the normal state on
disarming of the alarm. The LED’s and backlighting will turn off within 90 seconds of arming the system.
If this option is turned on and all areas assigned to a keypad are armed, the keypad display will be blank
during the armed state. If any keypad is assigned to more than one Area at location P71E, all areas
must be armed before the LED’s and Backlighting will go blank on arming.
Option 8 Turn Off LCD & Keypad Backlighting on Mains Fail - This option allows the backlighting on a keypad
(both the keypad buttons and the LCD module backlighting) to be turned off when there is a Mains
Failure. It is normally used to cut the power consumed by the keypad during a power failure. The LCD
backlighting will turn off within 90 seconds of the mains failing. If a button is pressed at the keypad the
backlighting will turn back on again. Following 90 seconds of no keypad activity the backlighting will turn
off. The LCD and Keypad backlighting will return to the normal state when Mains is restored.
KEYPAD <ARM> BUTTON AREA ASSIGNMENT
KEYPAD <ARM> BUTTON AREA ASSIGNMENT - P74E 1-32E Value = 01-32 for Areas 1-32
Option 01 Area “1” - This option assigns the keypad <ARM> button to Area 1. If a keypad <ARM> button is
assigned to only Area 1 it can only Arm or Disarm that area.
Option 32 Area “32” - This option assigns the keypad <ARM> button to Area 32. If a keypad <ARM> button is
assigned to only Area 32 it can only Arm or Disarm that area.
KEYPAD <ARM> BUTTON AREA OPTIONS
KEYPAD <ARM> BUTTON AREA OPTIONS - P75E 1-32E
Option 1 - <ARM> button can Arm
Option 2 - <ARM> button can Arm Stay Mode
Option 3 - <ARM> button can Disarm at All Times
Option 4 - <ARM> button can Disarm Stay Mode at All Times
Option 5 - <ARM> button can Reset Alarms
Option 6 - <ARM> button can Arm Latchkey Mode
Option 7 - <ARM> button can Disarm During Exit Delay
Option 8 - <ARM> button can Disarm Stay Mode During Exit Delay
Option 1 <ARM> button can Arm - This option enables single button Arming using the <ARM> button. For single
button operation to work options 1 & 3 must be off at location P45E.
Option 2 <ARM> button can Arm Stay Mode - This option enables single button Arming of Stay Mode using the
<ARM> button. For single button operation to work options 1 & 3 must be off at location P45E.
(NOTE: Following arming of Stay Mode, if the <ENTER> button is pressed, all entry & exit delays
will be reset to zero for that armed period).
Option 3 <ARM> button can Disarm at All Times - This option enables single button Disarming using the
<ARM> button. For single button disarm operation to work options 1 & 3 must be off at location P45E
Option 4 <ARM> button can Disarm Stay Mode at All Times - This option enables single button Disarming of
Stay Mode using the <ARM> button. For single button disarm operation to work options 1 & 3 must be
off at location P45E
Option 5 <ARM> button can Reset Alarms - If this option is On, Pressing the <ARM> button (provided Option 3
is also On) will reset an alarm condition without having to enter a user code.
Option 6 <ARM> button can Arm Latchkey Mode - This option enables single button Arming of the alarm in
Latchkey report mode using the <ARM> button. For single button disarm operation to work options 1 & 3
must be off at location P45E. When Latchkey Mode is set on Arming, any code without the Latchkey
To Next Page
Loading...
