D-Link DGS-3120-24PC - Chapter 51 Multicast VLAN Command List

xStack
®
DGS-3120 Series Layer 2 Managed Stackable Gigabit Switch CLI Reference Guide
503
Chapter 51 Multicast VLAN Command
List
create [igmp_snooping | mld_snooping] multicast_vlan <vlan_name 32> <vlanid 2-4094>
{remap_priority [<value 0-7> | none] {replace_priority}}
config igmp_snooping multicast_vlan <vlan_name 32> {[add | delete] [member_port <portlist> |
[source_port <portlist> |untag_source_port <portlist>] |tag_member_port <portlist>] | state
[enable|disable] | replace_source_ip [<ipaddr> | none] |remap_priority [<value 0-7> | none]
{ replace_priority}}(1)
config mld_snooping multicast_vlan <vlan_name 32> {[add | delete] [member_port <portlist> |
[source_port <portlist> | untag_source_port <portlist>] | tag_member_port <portlist>] | state
[enable | disable] | replace_source_ipv6 [<ipv6addr> | none] | remap_priority [<value 0-7> |
none] { replace_priority}}(1)
create [igmp_snooping | mld_snooping] multicast_vlan_group_profile <profile_name 1-32>
config igmp_snooping multicast_vlan_group_profile <profile_name 1-32> [add | delete]
<mcast_address_list>
config mld_snooping multicast_vlan_group_profile <profile_name 1-32> [add | delete]
<mcast_v6address_list>
delete [igmp_snooping | mld_snooping] multicast_vlan_group_profile [profile_name
<profile_name 1-32> | all]
show [igmp_snooping | mld_snooping ] multicast_vlan_group_profile {< profile_name 1-32>}
config [igmp_snooping | mld_snooping] multicast_vlan_group <vlan_name 32> [add | delete]
profile_name <profile_name 1-32>
show [igmp_snooping | mld_snooping] multicast_vlan_group {<vlan_name 32>}
delete [igmp_snooping | mld_snooping] multicast_vlan <vlan_name 32>
enable [igmp_snooping | mld_snooping] multicast_vlan
disable [igmp_snooping | mld_snooping] multicast_vlan
config [igmp_snooping | mld_snooping] multicast_vlan forward_unmatched [enable |
disable]
show [igmp_snooping | mld_snooping] multicast_vlan {<vlan_name 32>}
51-1 create [igmp_snooping | mld_snooping] multicast_vlan
Description
This command is used to create a multicast VLAN and implements relevant parameters as
specified. More than one multicast VLANs can be configured. The maximum number of
configurable VLANs is project dependent.
Newly created IGMP snooping multicast VLANs must use a unique VLAN ID and name, i.e. they
cannot use the VLAN ID or name of any existing 802.1q VLAN.
Also keep in mind the following conditions:
• Multicast VLANs cannot be configured or displayed using 802.1Q VLAN commands.
• An IP interface cannot be bound to a multicast VLAN.
• The multicast VLAN snooping function co-exists with the 802.1q VLAN snooping function.