D-Link DSR-150 User Manual

D-Link DSR-Series User Manual 245
Section 9 - Maintenance
Field Description
Remote Log Identier
Enter a prex used to identify the source of the message. This identier is prexed to both e-mail
and Syslog messages.
E-Mail Log Toggle to ON to enable E-Mail logs.
E-Mail Server Address
Enter the IP address or network address of the SMTP server. The router will connect to this server
to send e-mail logs when required. The SMTP server must be operational for e-mail notications
to be received.
SMTP Port Enter the SMTP port of the e-mail server.
Return E-Mail Address
Enter the e-mail address where replies from the SMTP server are to be sent (required for failure
messages).
Send to E-Mail Address (1-3) Enter up to three e-mail addresses where logs and alerts are to be sent.
Authentication with SMTP
Select an authentication if the SMTP server requires authentication before accepting connections.
Choices are:
• None: No authentication is used. The User Name and Password elds are not available.
• Plain Login: Authentication used to log in using Base64-encoded passwords over non-
encrypted communication session. Base64-encoded passwords oer no cryptographic
protection, making them vulnerable.
• CRAM-MD5: A challenge-response authentication mechanism dened in RFC 2195 based on
the HMAC-MD5 MAC algorithm. CRAM-MD5 oers a higher level of authentication than Login
Plain.
User Name
If Authentication with SMTP is set to Login Plain or CRAM-MD5, enter the user name to be used for
authentication.
Password
If Authentication with SMTP is set to Login Plain or CRAM-MD5, enter the case-sensitive password
to be used for authentication.
Enable Tls
If the SMTP server requires Tls support to sent logs through emails, this option should be enabled
and is available only for authentication methods Plain Login or CRAM-MD5.
Respond to identd from
SMTP
Toggle to ON to have the router respond to IDENT requests from the SMTP server.
Unit
Select the period of time that you need to send the log. This option is useful when you do not want
to receive logs by e-mail, but want to keep e-mail options congured, so you can use the Send Log
function Event Log viewer pages. Choices are:
• Never: Disable sending of logs.
• Hourly: Send logs every hour.
• Daily: Send logs every day at the Time specied.
• Weekly: Send logs weekly, at the Day and Time specied.
Day If Unit is set to Weekly, select the day of the week when logs will be sent.
Time If Unit is set to Daily or Weekly, select the time when logs will be sent.
Save Click save and activate your settings.

D-Link DSR-150 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100Base-T(X)
Networking standards	IEEE 802.1Q, IEEE 802.3, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s
Ethernet interface type	Fast Ethernet
PC in (D-Sub)	No
USB ports quantity	0
Ethernet LAN (RJ-45) ports	8
Supported network protocols	IPSec, PPTP, L2TP
Security algorithms	3DES, DES, SSL/TLS
VPN tunnels quantity	21
Filtering description	Keyword
MAC address filtering	-
Safety	cUL, LVD (EN60950-1)
Certification	WEEE
Electromagnetic compatibility	FCC Class B, CE Class B, C-Tick, IC
Mean time between failures (MTBF)	240000 h
Input current	1.5 A
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (typical)	7.44 W
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	5 - 95 %
Product color	Black
Input voltage	12 V
Ports quantity	The number of ports or external interfaces to which other equipment can be connected.
Management platform	HTTP, HTTPS, CLI, SNMP v1/v2c/v3
Connectivity technology	Wired
Compliance industry standards	RoHS

Weight and Dimensions

Depth	118 mm
Width	208 mm
Height	35 mm
Weight	- g