Name: Delta VFD-V Series
Brand: Delta
Rating: 4 (1 reviews)

Default Chapter4

Chapter 1 Receiving and Inspection8

Chapter 2 Storage and Installation10

Installation11

Chapter 3 Wiring12

Chapter 4 Digital Keypad (Vfd-Pu05) Operation28

Chapter 5 Description of Parameter Settings32

Parameter Reset33
Definitions of the Multi-Function Display34
Start-Up Display of the Drive34
User-Defined Coefficient Setting35
Frequency and the Operation Method of PU0536
Control Methods37
Forward Reverse Transition in V/F Mode38
Constant Torque Operation Selection39
Optimal Acceleration/Deceleration Setting39
Time Unit for Acceleration/Deceleration and S Curve39
Carrier Frequency Lower Bound40
Carrier Frequency Upper Bound40
Center Frequency of Soft Pwm40
Auto Voltage Regulation (AVR) Function41
Automatic Energy-Saving Operation41
Source of the Frequency Command42
Source of the Operation Command42
Stop Methods42
Reverse Operation43
Group 1: Basic Parameter44
- Maximum Output Frequency44
- Maximum Output Voltage44
- Upper Midpoint Output Voltage44
- Lower Bound Frequency45
- Startup Frequency45
- Upper Bound Frequency45
- Acceleration Time46
- Deceleration Time46
- JOG Acceleration Time46
- JOG Deceleration Time46
- 1Th/4Th Acceleration/Deceleration Frequency47
- JOG Frequency47
- S-Curve for Acceleration Arrival Time48
- S-Curve for Acceleration Departure Time48
- S-Curve for Deceleration Arrival Time48
- S-Curve for Deceleration Departure Time48
- Skip Frequency49
- 2-Wire/3-Wire Operation Control50
Group 2: Digital Output/Input Parameter50
- Full List of the Functions51
- Multi-Function Input Command51
- Acceleration/Deceleration Speed of UP/DOWN Key with Constant Speed54
- Digital Input Responding Time54
- UP/DOWN Key Mode54
- Digital Input Operation Direction55
- Multi-Function Output55
- Multi-Function Output Direction56
- Counter Values Achieve the Pre-Set Values57
- Designated Counter Value Achieved57
- Digital Output Gain58
- Pre-Set Arrival Frequency58
- (ACI) Analog Input Bias 259
- (AUI) Analog Input Bias 359
- (AVI) Analog Input Bias 159
Group 3: Analog Output/Input Parameter59
- (ACI) Positive/Negative Bias Mode60
- (AUI) Positive/Negative Bias Mode60
- (AVI) Positive/Negative Bias Mode60
- Addition Function of the Analog Inputs61
- Analog Input 1 Gain (AVI)61
- Analog Input 2 Gain (ACI)61
- Analog Input 3 Gain (AUI)61
- Analog Input Noise Filter64
- Analog Output Selection64
- Loss of the ACI Signal64
- Analog Output Gain65
- Analog Output Bias Voltage66
- Analog Output Value in REV Direction66
- Multi-Step Speed and Process Control Operation (PCO)67
- The PCO Operation Direction68
- The PCO Time Multiplier68
- Time Duration of the PCO Master Speed68
- Multi-Step Speed Operation Mode70
- Process Control Operation Mode70
- Disable Skip Frequency Width71
- Interfere Jump Width71
- Motor Auto Tuning72
- Motor Parameters72
- Full-Load Current of Motor 173
- No-Load Current of Motor 173
- Slip Compensation of Motor 1 (for V/F Mode Only)73
- Torque Compensation of Motor 1 (for the V/F Mode Only)73
- Full-Load Current of Motor 2/No-Load Current of Motor 274
- Iron Loss of Motor 174
- LC of Motor 174
- Number of Poles for Motor 174
- ASR I (Integration) Time 175
- Frequency Switch between ASR1 and 275
- Iron Loss of Motor 275
- LC of Motor 275
- Low-Speed Excitation Magnet Compensation76
- R1 Detection Frequency76
- Time Delay of the Pre-Controlled Torque Feedback76
- Vibration Compensation Factor76
Group 6: Protection Parameter77
- Low Voltage Level77
- Over-Voltage Stall Prevention77
- Over-Current Stall Prevention During Acceleration78
- Phase-Loss Protection78
- Over-Current Deceleration Time During Operation79
- Over-Current Stall Prevention During Operation79
- Over-Torque Detection Level (Ol2)79
- Over-Torque Detection Selection (Ol2)79
- Over-Torque Detection Level 2 (OL3)80
- Over-Torque Detection Selection 2 (OL3)80
- Over-Torque Detection Time (Ol2)80
- Over-Torque Detection Time 2 (OL3)80
- Electronic Thermal Relay Selection81
- Electronic Thermal Relay Time81
- Heat Sink Over-Heat (Oh) Warning81
- Over-Torque Limit81
- Most Recent Fault Record82
- Op Stall Low Limit82
- DC Braking Current Level84
- DC Braking Time at Start-Up/DC Braking Time During a STOP84
Group 7: Special Parameter84
- Software Braking Level84
- Increasing Rate of the DC Voltage85
- Base Block Time for Speed Search86
- Maximum Allowable Power Loss Time86
- Maximum Current Level for Speed Search86
- Re-Activate after Momentary Power Loss86
- Auto Restart after Fault87
- Deceleration Time for Speed Search87
- Speed Search Frequency (FWD Direction)88
- Speed Search Frequency (REV Direction)88
- Speed Search Type88
- External Terminals RUN after Fault Reset89
- Gear Gap Acceleration-Interruption Frequency89
- Gear Gap Acceleration-Interruption Time89
- Gear Gap Deceleration-Interruption Time/Frequency89
Group 8: High-Performance Parameter90
- Integral Time (I)/Differential Time (D)90
- Integration’s Upper Bound Frequency90
- PID Feedback Terminal Selection/Proportional Gain (P)90
- One-Time Delay91
- PID Deviation Range91
- PID Frequency Output Command Limit91
- Detection Time of the Feedback Error92
- Dwell (Sleep) Frequency92
- Feedback Signal Fault Treatment92
- Revival Frequency/Dwell (Sleep) Period92
- Fan Control93
- Communication Address94
Group 9: Communication Parameter94
- Transmission Fault Treatment/Overtime Detection/Communication Protocol94
- Transmission Speed of the Communication94
- Meaning of Encoding95
- WORD Structure95
- Communication Data Structure96
- The Data Format Frame96
- Function Code and Data Contents98
- The CRC Check of the RTU Mode100
- The LRC Check of the ASCII Mode100
- Definition of the Parameters Addresses of the Communication Protocol101
- Additional Response During Erroneous Communication103
- Keypad Transmission Fault Treatment104
- Encoder Input Setting (Channel 1)105
Group 10: Speed Feedback Parameter105
- PG (Encoder) Pulses105
- PG Feedback Fault Detection Time106
- PG Feedback Fault Treatment106
- PG Feedback Filter Time106
- PG Electrical Gear A/Gear B107
- PG Position Control Point (Home)/Range for PG Position Attained107
- PG Slip Range107
- PG Stall Level (Overspeed Protection)107
- PG Encoder Input Filter Time108
- PG04 Encoder Input Selection (Channel 2)108
- Position Control Parameter109
- Feed Forward110
- Position Control Speed Gain110
- Delay Time for Position Command111
- Direction Command of Absolute P2P111
- PG Position Attained 2111
- Selection of P2P Control Mode111
- REV Limit of Absolute P2P112

Chapter 6 Maintenance and Inspections114

Error Message and Troubleshooting116

Chapter 7 Troubleshooting116

System Parameter122

Chapter 8 Parameter Summary122

Appendix A Specifications156

Appendix B Accessories156

Appendix C Dimensions174

The Apparatus Size of the Digital Hand-Held Programming Panel VFD-PU05182

Appendix D Ec Declaration of Conformity184

Brand	Delta
Model	VFD-V Series
Category	Controller
Language	English

Delta VFD-V Series User Manual

Table of Contents

Questions and Answers:

Delta VFD-V Series Specifications

Related product manuals