TABLE OF CONTENTS
Page III © 2005 DH Instruments, Inc.
4.3 LOCAL OPERATION, ADCS TOOLS....................................................................................................67
4.3.1 OVERVIEW ..................................................................................................................................................67
4.3.2 MAIN MENU.................................................................................................................................................69
4.3.3 ADCS MAIN TOOLBARS ............................................................................................................................70
4.3.4 ADCS STATUS BAR....................................................................................................................................74
4.3.5 ADCS RUN SCREEN...................................................................................................................................74
4.3.5.1 ADCS RUN SCREEN CONTROL PANEL ...............................................................................................75
4.3.5.2 ADCS SYSTEM DISPLAY .......................................................................................................................76
4.3.5.3 ADCS RUN SCREEN TOOLBAR ............................................................................................................78
4.3.6 OTHER DEVICE RUN SCREENS ...............................................................................................................79
4.3.6.1 PG7601 PRESSURE STANDARD...........................................................................................................79
4.3.6.2 FPG8601 PRESSURE STANDARD ........................................................................................................80
4.3.6.3 PPC3 (FPG’S PRESSURE CONTROLLER)............................................................................................80
4.3.6.4 RPM4 REFERENCE PRESSURE MONITOR .........................................................................................81
4.4 AUTOMATED TESTING ........................................................................................................................82
4.4.1 SETTING UP TO RUN AUTOMATED TESTS.............................................................................................82
4.4.1.1 SETTING UP DEVICE UNDER TEST (DUT)...........................................................................................82
4.4.1.2 SETTING UP TEST DEFINITIONS..........................................................................................................84
4.4.1.3 SETTING UP SUPPORT DEVICES.........................................................................................................85
4.4.1.4 TEST OPTIONS (DATA OPTIONS).........................................................................................................85
4.4.2 RUNNING AUTOMATED TESTS ................................................................................................................86
4.4.2.1 RUNNING A MANUAL TEST...................................................................................................................87
4.4.2.2 RUNNING A TEST DEFINITION..............................................................................................................87
4.4.3 TEST RUN SCREENS .................................................................................................................................88
4.4.3.1 DATA PLOT RUN SCREEN.....................................................................................................................89
4.4.3.2 DATA GRID RUN SCREEN.....................................................................................................................89
4.4.3.3 DUT/REFERENCE COMPARISON RUN SCREEN ................................................................................90
4.4.4 TEST DATA..................................................................................................................................................91
4.4.5 REPORT EDITOR........................................................................................................................................91
4.4.6 RUNNING A MODEL 3682 AIR DATA CALIBRATOR................................................................................92
4.4.6.1 RUNNING A VALIDATION (CALIBRATION) ...........................................................................................92
4.4.6.2 RUNNING A STANDARDIZATION ..........................................................................................................97
5. REMOTE OPERATION ......................................................103
6. GENERAL MAINTENANCE AND ADJUSTMENTS ..................105
6.1 SUMMARY ...........................................................................................................................................105
6.2 FPG8601, CHECK BUBBLER AND ADD WATER IF NECESSARY...................................................106
6.3 FPG8601, REMOVE CLEAN AND REINSTALL THE PISTON-CYLINDER........................................107
6.3.1 OVERVIEW ................................................................................................................................................107
6.3.2 REMOVING THE PISTON-CYLINDER FROM THE MOUNTING POST...................................................109
6.3.3 REMOVING THE PISTON FROM THE CYLINDER ..................................................................................111
6.3.4 CLEANING THE PISTON AND CYLINDER ..............................................................................................112
6.3.5 PUTTING THE PISTON INTO THE CYLINDER........................................................................................113
6.3.6 INSTALLING THE PISTON-CYLINDER IN THE MOUNTING POST.................................................114
6.3.7 RESTORING PISTON-CYLINDER LUBRICATION AND MOBILITY........................................................115
6.3.7.1 OVERVIEW............................................................................................................................................115
6.3.7.2 PISTON CENTERING AND LUBRICATING METHODS.......................................................................115
6.4 PG7601, DISASSEMBLE PLATFORM AND REMOVE MOUNTING POST PRT................................117
6.5 PG7601, REMOVE AND REINSTALL THE AUTOMATED MASS HANDLER AND MASS SET ........118
6.5.1 THE MASS HANDLER (AMH)...................................................................................................................118
6.5.2 THE MASS SET.........................................................................................................................................121
6.6 PG7601, REMOVE, CLEAN AND REINSTALL THE PISTON-CYLINDER MODULE.........................122
6.6.1 REMOVING THE PISTON-CYLINDER MODULE .....................................................................................122
6.6.2 INSTALLING THE PISTON-CYLINDER MODULE ...................................................................................123
6.6.3 DISASSEMBLING THE MODULE AND CLEANING THE PISTON-CYLINDER ASSEMBLY..................124
6.6.3.1 OVERVIEW............................................................................................................................................124
6.6.3.2 DISASSEMBLING AND REASSEMBLING THE MODULE ...................................................................124
6.6.3.3 LUBRICATING THE PISTON-CYLINDER MODULE.............................................................................127
6.6.3.4 CLEANING THE PISTON-CYLINDER...................................................................................................128
6.7 PG7601, PISTON POSITION DETECTION ADJUSTMENT................................................................130
6.8 PG7601, REPLACE PISTON ROTATION DRIVE BELTS...................................................................131
6.9 PG7601, ADJUST INTERNAL VACUUM GAUGE...............................................................................131
6.10 PG7601/FPG8601, ADJUST PPC3 PRESSURE CONTROLLERS.....................................................132
To Next Page
Loading...