EasyManuals Logo

Dräger X-am 7000 Instructions For Use

Dräger X-am 7000
92 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #40 background imageLoading...
Page #40 background image
40
Тревога без звука
Эта функция позволяет отключить звуковой сигнал тревоги.
Выберите элементы меню » Settings \ Instrument \ Silent
alarm « в указанном порядке, нажимая кнопку »
OK
« после
каждого выбора.
Выберите желательное состояние » Enable « (включить) или
» Disable « (отключить) и нажмите кнопку »
OK
«, чтобы акти
визировать выбранную опцию.
Когда активна опция » Enable «, звуковой сигнал тревоги вык
лючен. На это указывает значок » « в правой части дисплея.
Звуковой сигнал тревоги автоматически активизируется
после выключения инструмента, но назначение функцио
нальной кнопки сохраняется.
Сигнал работы прибора
Эта функция позволяет включать/отключать сигнал работы
прибора. Cигнал работы, указывающий на работоспособ
ность прибора, активирован по умолчанию в поставляемом
с завода инструменте; он требуется для надежного исполь
зования инструмента в качестве газосигнализатора.
Выберите элементы меню » Settings \ Instrument \ Life signal
« в указанном порядке, нажимая кнопку »
OK
« после каждого
выбора.
Выберите желательное состояние » Enable « (включить) или
» Disable « (отключить) и нажмите кнопку »
OK
«, чтобы акти
визировать выбранную опцию.
Когда активна опция » Enable «, в режиме измерения каждые
30 секунд генерируются световой и звуковой сигналы.
Silent alarm
This function is used to switch the of audible alarm.
Select the menu items » Settings \ Instrument \ Silent alarm « in
this order, pressing the »
OK
« key after each selection.
Select the desired state » Enable « or » Disable « and press the
»
OK
« key to activate it.
When the state » Enable « is active, the audible alarm is switched
off. This is indicated by the icon » « on the right side of the dis
play.
The audible alarm is automatically reactivated when the instru
ment is switched off, but the functionkey assignment remains
unchanged.
Life signal
This function is used to switch the life signal on or off. The lie
signal, which indicates that the instrument is operating correct
ly, is activated when the instrument leaves the factory and is re
quired for reliable use of the instrument as a gaswarning de
vice.
Select the menu items » Settings \ Instrument \ Life signal « in
this order, pressing the »
OK
« key after each selection.
Select the desired state » Enable « or » Disable « and press the
»
OK
« key to activate it.
If the state » Enable « is active, optical and audible signals are gen
erated every 30 seconds in measuring mode.

Table of Contents

Other manuals for Dräger X-am 7000

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Dräger X-am 7000 and is the answer not in the manual?

Dräger X-am 7000 Specifications

General IconGeneral
TypePortable gas detector
DisplayLCD with backlight
Ingress ProtectionIP67
Humidity10 to 95% RH, non-condensing
SensorsElectrochemical
AlarmVisual, Audible, and Vibration
Power SupplyRechargeable NiMH battery or Alkaline batteries
Operating Temperature-20°C to +50°C
Data LoggingYes
Gases DetectedOxygen (O2), Combustible gases (LEL), Carbon monoxide (CO), Hydrogen sulfide (H2S)

Related product manuals