DragonWave Horizon COMPACT - Page 140

Horizon Compact Release 1.01.00 Wireless Ethernet Product User Manual – Volume 2
get transmit power
get unique peer authentication key
get user accounts
get user session
get vlan tag
get vlan tagging
get web server
kill ssh sessions
list [ftp:file/directory/]
lo
ping [-w timeout][-n count][-t][ip address]
reset [system / modem]
save config [ftp:filename]
save log [ftp:filename]
save mib
save performance log [ftp:filename]
save users [ftp:filename]
set aam [on/off]
set admin user
set air interface authentication type [type]
set authentication failure [action]
set alarms counter [0]
set alignment [on/off]
set antenna diameter [index of diameter]
set atpc [on|off][coordinated power]
set bandwidth utilization threshold [threshold][time]
set cos default value [0-7]
set cos expedite queue [on|off]
set cos qinq itag [protocol id]
set cos qinq otag [protocol id]
set cos queue cir [0-100,0-100,0-100,1-100]
set cos queue mapping [mapping]
set cos queue cbs
set cos type [cos_vlan][cos_qinq_itag][cos_qinq_otag]
set current channel index
set date time [dd/mm/yyyy hh:mm:ss:ms]
set default gateway [ip address]
set dropped frames threshold [threshold][time]
set enet config [port1|port2]
set enet speed [port1|port2] speed[10|100|1000|auto]
AutoNeg[auto]
set frequency bank
set group authentication key [key]
set http secure access [Admin|Noc|Super] [on|off]
set ip address [address]
set logging [on|off]
set maximum frame size [1600-9600]
set network management interface [port1|port2| port2
extended]
set network protocol strict [on|off]
set noc user
set optical transmitter state [on|off]
set pause state [on|off]
set performance logging [on|off]
set performance log interval [hr:min:sec]
set programmed frequency [index]
set qos [on|off]
set radio transmitter state [enable|disable]
set radio band [band]
set radio loopback [on|off]
set radio rxgain
set radio txgain
set radius server key [index] [key]
set radius server host [index] [ip address]
set radius super user authentication strict [on|off]
set redundancy link monitor parameters
set redundancy mode
set redundancy override [primary|secondary|
manual|auto]
set redundancy standby enet state [on/off/pulse]
set redundancy state switch
set rls [on|off]
set rls link enable [on|off]
set rls link monitor parameters [dn2up frame error]
[up2dn frame error] [dn2up samples] [up2dn samples]
[sample time]
set rls link control [on|off]
set rls make rsl [rsl value][time]
set rls signal fault parameters [time][% error]
set rsl threshold [threshold][time]
set snmp access mode [v1|v2c|off]
set snmp manager [mgr index] [ip address]
[enable|disable] [community string]
set snmp set request [on|off]
set snmp trap [trap#] [enable|disable]
set snmp trap host [host#] [ip address]
[enable|disable] [community string]
set snr threshold [threshold]
set snmpv3 trap host enable [index]
set snmpv3 trap host disable [index]
set snmpv3 trap host ip [index] [ip address]
set snmpv3 trap host user [index] [none|des]
set snmpv3 trap host authentication [indes]
[none|md5|sha] [passwd]
set snmpv3 trap host privacy [index] [none|des]
set sntp [on|off]
set sntp default
set sntp offset [hrs]
set sntp server [index] [ip address]
set ssh server
set super user [username] [password]
set system current speed [speed]
set system mode [mode]
set system redundancy [on|off]
set telnet [on|off]
set traffic statistics [0]
set transmit power [power in dB]
set unique peer authentication key [key]
set subnet mask [mask]
set vlan tag [vlan ID (0-4095)] [vlan priority (0-7)]
set vlan tagging [on|off]
set web server [on|off]
upgrade system licensed speed [speed] [key]