13
EA(B)O-6X06 01/2018 Rev. 1 1. General Information
Tightening Torques and Sealants
Item Description Torque N.m (Lb.ft) Remarks
Front Case Assy.
110 Front case
Apply Dow Corning 780 sealant onto
the contact face with the rear case
111 PTO cover
Apply Dow Corning 780 sealant onto
the contact face
112 M10 x 1.5 x 16 Screw 30-35 (22-25)
113 M12 x 1.0 Pivot pin 19-26 (14-19)
Apply Dow Corning 780 sealant onto
thread and contact face*
114 3/4”-14 NPTF Oil ll plug 20-34 (15-25) Apply Loctite 570 (Eaton E677)
115 1/8"-27 NPTF breather 6-10 (4-7)
Apply Dow Corning 780 sealant onto
thread and contact face*
120 M6x1.0-6.5 Socket screw 6-9 (4-6)
121 M8 x 1.25 x 25 Screw 19-26 (14-19)
Apply Dow Corning 780 sealant onto
thread and contact face*
123 M6 x 1.0 x 25 Allen screw 11-14 (8-10)
125 M6 x 1.0 x 14 Screw 12-15 (9-11)
126 3/4”-14 NPTF Oil drain plug 20-34 (15-25) Apply Loctite 570 (Eaton E677)
129
Clutch release bearing sleeve (input
shaft front bearing cover)
Apply Dow Corning 780 sealant onto
the contact face
131 M8 x 1.25 x 16 Screw 19-26 (14-19)
132 M8 x 1.25 x 45 Screw 19-26 (14-19)
Apply Dow Corning 780 sealant onto
the contact face*
133 Ball stud 110-120 (81-88)
138 M6 x 1.0 x 14 Screw 12-15 (9-11)
Rear Case Assy.
140 Rear case
Apply Dow Corning 780 sealant onto
the contact face with the front case
142 M8 x 1.25 x 25 Screw 19-26 (14-19)
144 M6 x 1.0 x 14 Screw 12-15 (9-11)
147 Shift actuator plug 28-32 (20-23)
Apply Dow Corning 780 sealant onto
thread and contact face*
148 M8 x 1.25 x 45 Screw 19-26 (14-19)
151 Washer
Apply Dow Corning 780 sealant onto
both contact faces with yoke and screw
152 M16 x 1.5 x 55 Bolt 109-122 (80-89)
153 Threaded plug 19-26 (14-19)
Apply Dow Corning 780 sealant onto
thread and contact face*
156 M8 x 1.25 x 20 Screw 19-26 (14-19)
157 Speedometer sensor 14-20 (10-15)
Apply Dow Corning 780 sealant onto
the contact face*
158 Reverse idle gear cover
Apply Dow Corning 780 sealant onto
the contact face
159 M6 x 1.0 x 14 Screw 12-15 (9-11)
161 M14 X 2 X 34 Allen screw 108-122 (80-90) Apply Loctite 262 onto thread
* Apply sealant onto the contact surface of screws and plugs with the transmission case.
To Next Page
Loading...
