Emerson Rosemount 3100 Series - Menus on the 3102 and the 3105

Reference Manual
00809-0100-4840, Rev. BA
July 2008
C-3
Rosemount 3100 Series
MENUS ON THE 3102
AND THE 3105
Figure C-2. Main Menu Programming on The 3102/3105
PV Display
(Diagnostics ) (Duty)
Diagnostics (Loop test ) (Distance) (PV)
Loop test (Eng setup ) (PV )
Eng setup (PV)
(2s)
(2s)
duty
(Display Duty) (unitS)
unitS
(Display Base Units ) (b.rEF)
b.rEF
(Display Bottom Ref ) (ProF)
Display Duty (Start duty edit) (duty)
ProF
(Display N-L Profile ) (SCALE/‘Duty’@max)
SCALE
(Display Scale Factor) (4)
4
(Display 4mA value) (20)
20
(Display 20m A value ) (d)
d
(Display Damping ) (AL)
Start duty edit (Scroll thru duties ) (Confirm duty )
Confirm Duty (Not save; duty ) (Save; unitS)
Display Base Units (Start units edit ) (unitS)
Start units edit (Scroll thru units ) (Confirm units )
Confirm Units (Not save; unitS ) (Save; b.rEF)
Display Bottom Ref (Start Bottom Reference edit ) (b.rEF)
Start B ottom Ref ed it (Edit flashing digit) (Confirm edit/B.Ref)
Confirm Bottom Ref (Not save; b.rEF) (Save; ProF/SCALE )
Display N -L Profile (Start profile edit) (ProF)
Start profile edit (Scroll thru profiles) (Confirm profile)
Confirm Profile (Not save; ProF) (Save; SCALE)
Display 4mA value (Start 4mA edit) (4)
Display 4mA value (Not save; 4) (Save it ; 20)
Display 20mA value (Start 20mA edit) (20 )
Display 20mA value (Not save; 20) (Save it ; d)
Display Damping (Start damping edit) (d)
Display Damping (Not save; d) (Save; AL)
1
1
r1.On
(Display RL1 On Pt) (r1. Off)
Display RL 1 On Pt (Start edit) (r1.On)
r1.OFF
(Display RL1 Off Pt) (r2. On)
Display RL 1 Off Pt (Start edit) (r1.OFF)
Confirm RL1 Off Pt (Not save; r1.OFF) (Save ; r2.On )
r2.On
(Display RL2 On Pt) (r2. Off)
Display RL 2 On Pt (Start edit) (r2.On)
Display RL 2 On Pt (Not save; r2.On) (Save it ; r2.OFF)
r2.OFF
(Display RL2 Off Pt) (SEt 4)
Display RL 2 Off Pt (Start edit) (r2.OFF)
Display RL 2 Off Pt (Not save; r2.OFF) (Save; SEt 4)
SEt 4
(Display PV @ 4 mA) (SEt 20 )
Display PV @ 4mA (Ranging) (SEt 4)
Ranging (Flash “4” and PV )
Display PV @ 4mA (Not save; SEt 4) (Save; SEt 20)
SEt 20
(Display PV @ 20 mA) (PV Display)
Display PV @ 20mA (Ranging) (SEt 20)
Ranging (Flash “20” and PV)
Display PV @ 20mA (Not save; SEt 20 ) (Save; PV Display)
(See Diagnostics menu )
AL
(Display Alarm Current Action ) (AL )
Display Alarm Current Action (Start selection) (AL)
Start Selection (Scroll thru options) (Confirm selection)
Confirm selection (Not save ; AL) (Save; r1.OFF or SEt 4)
Level
@max
(Display max level) (‘Duty’ @ max)
Display max level (Start max level edit) (Level @m ax)
Start max level edit (Edit flashing digit) (Confirm digit edit / max level)
Confirm max level (Not save; Level @max) (Save; ‘Duty’@max)
Display Scale Factor (Start S -Factor edit ) (SCALE)
Start Scale Factor edit (Edit flashing digit) (Confirm digit edit / Scale Factor)
Confirm Scale Factor (Not Save; SCALE) (Save; 4)
Content / Flow
Start 4mA edit (Edit flashing digit) (Confirm digit edit / 4mA value)
Start 20mA edit (Edit flashing digit) (Confirm digit edit / 20mA value) Start damping edit (Edit flashing digit) (Confirm digit edit / damping value)
Start RL1 On Pt edit (Edit flashing digit) (Confirm digit edit / RL1 On Pt)
Confirm RL1 On Pt (Not save; r1.On) (Save; r1.Off)
Start RL1 Off Pt edit (Edit flashing digit) (Confirm digit edit / RL1 Off Pt)
Model 3102
Model 3102Model 3102Model 3102
Start RL2 On Pt edit (Edit flashing digit) (Confirm digit edit / RL2 On Pt) Start RL2 Off Pt edit (Edit flashing digit) (Confirm digit edit / RL2 Off Pt)
(4mA Ranging)(20mA Ranging)
Content / Flow Leve l / Dista nce
Flow
@max
(Display max level) (4)
Display max flow (Start max flow edit) (Flow @max)
Start max flow edit (Edit flashing digit) (Confirm digit edit / max flow)
Confirm max flow (Not save; Flow @max) (Save; 4)
Flow
Cont
@max
(Display max content) (4)
Display max content (Start max cont edit) (C ont @ max)
Start max cont edit (Edit flashing digit) (Confirm digit edit / max contents)
Confirm max cont (Not save; Cont @max) (Save; 4)
Contents (Volume)