EMKO EPC-1 - 6.2 EASY ACCESSING DIAGRAM FOR PAGES

To Next Page

To Previous Page

6.2 EASY ACCESSING DIAGRAM FOR PAGES

TECHNICIAN

PASSWORD

0000

How to access to technician pages?

There must be no selected parameter in current page.

The current page must be one of the following pages which are in user field;

PROCESS VALUES, SYSTEM MONITORING, FEEDING CONSUMPTION, WEIGHING1 LOG,

WEIGHING2 LOG, WEIGHING3 LOG, ELECTRICITY ENERGY CONSUMPTION, WATER CONSUMPTION,

SET VALUES, SET SHUTTER, FEEDING PARAMETERS, LIGHTING PARAMETERS, ALARM SET VALUES,

PROCESS OUTPUTS, MAX MIN VALUES 1, MAX MIN VALUES 2, EVENTS

Under these conditions, push button.

This page will be seen;

If right password is entered, then HEATING1 PARAMETERS page which is the first page of the

technician pages is accessed.

HEATING1 PARAMETERS

SENSOR : ROOM1

CONTROL :PROPORTION

SET POINT: RELATIVE

HYST : 1.0°C

PERIOD : 40SEC

OFFSET : 0.0°C

PROP RAMP: 50SEC

HEATING2 PARAMETERS

SENSOR : ROOM1

CONTROL :PROPORTION

SET POINT: RELATIVE

HYST : 1.0°C

PERIOD : 40SEC

OFFSET : 0.0°C

PROP RAMP: 50SEC

COOLING PARAMETERS

SENSOR : ROOM1

CONTROL :PROPORTION

SET POINT: RELATIVE

HYST : 1.0°C

PERIOD : 40SEC

OFFSET : 0.0°C

PROP RAMP: 50SEC

HUMIDITY

CONTROL :PROPORTION

HYST : 10%

PERIOD : 40SEC

OFFSET : 0%

PROP RAMP: 50SEC

VENTIL. PARAMETERS

SHIFTING : ON

SHIFT&PRP PER: 10MIN

DLY BTWN FANS: 5SEC

PRPRTN RAMP : 50SEC

SENSOR : ROOM1

FAN CONT.: TUNNEL

SET VENTILATION<°C>

VENT1: 0.5 VENT3: 2.5

VENT2: 1.0 VENT3: 3.0

VENT3: 1.5 VENT3: 3.5

VENT4: 2.0 VENT3: 4.0

SHUTTER PARAMETERS

STROKE TIME: 100SEC

STEP : 0.1%

TEMPERATURE SETTINGS

ROOM1 OFFSET: 0.0°C

ROOM2 OFFSET: 0.0°C

OUT. OFFSET : 0.0°C

HUM. OFFSET : 0%

SENS MINMAX : ROOM1&2

SENS OPENING: ROOM1&2

CONTROL FUNC PAGE 1

CURVE : DISABLE

HUMIDITY : ENABLE

OUTSIDE TEMP: ENABLE

COMMUNICATE : ENABLE

LOAD DEFAULT: NO

WATER CONSUM: ENABLE

ELECT CONSUM: ENABLE

CONTROL FUNC PAGE 2

FEEDING : ENABLE

CHICKS W1 : ENABLE

CHICKS W2 : ENABLE

CHICKS W3 : ENABLE

LIGHTING : ENABLE

LIGHT CONT: MODULATE

FEED UNIT PARAMETERS

UNIT : TIME

FEED PER MIN: 6.0KG

TARE : NO

REF WEIGHT : 250KG

TAKE REF WEIGHT: NO

FEED OFFSET : 0KG

WEIGHT1 CALIBRATION

TARE: NO

REF WEIGHT: 5000GR

TAKE REF WEIGHT: NO

5000GR

WEIGHT2 CALIBRATION

TARE: NO

REF WEIGHT: 5000GR

TAKE REF WEIGHT: NO

5000GR

WEIGHT3 CALIBRATION

TARE: NO

REF WEIGHT: 5000GR

TAKE REF WEIGHT: NO

5000GR

AVERAGE WEIGH1

INITIAL WEIGH: 100GR

MINIMUM LIMIT: 30%

MAXIMUM LIMIT: 15%

AVERAGE WEIGH2

INITIAL WEIGH: 100GR

MINIMUM LIMIT: 30%

MAXIMUM LIMIT: 15%

AVERAGE WEIGH3

INITIAL WEIGH: 100GR

MINIMUM LIMIT: 30%

MAXIMUM LIMIT: 15%

WEIGHING PARAMETERS

SS TIME : 1.0SEC

SS LIMIT VAL: 15GR

AW MIN SMPL : 100

AW SMPL PER : 2HR

WATER AND ELECTRICITY

CONSUMPTION PER PULSE

ELECTRICITY: 1000WH/P

WATER : 0.10LT/P

MODBUS

BAUD RATE : 3

STOP BIT : 0

PARITY BIT: 0

SLAVE ID : 1

EDIT PASSWORDS

TECHNICIAN: 0000

USER : 0000

ENTER CAL

PASSWORD

0000

NOTES:

1: If CONTROL FUNC PAGE 2 PAGE FEEDING