EMKO TRANS-AMF - Mains and Generator Technical Parameters; Mains Voltage and Frequency Actions; Generator Voltage and Frequency Settings

32
600
60
60
60
600
600
600
VV
VV
VV
VV
60
Min
DefaultMAINS VOLT LEVEL (Mains->Volt level)
Max
Mains Under Voltage
Mains Under Voltage Reset
Mains Over Voltage
Mains Over Voltage Reset
320
340
440
420
Under volt trip
4.2.2 Mains
Under volt reset
Over volt trip
Over volt reset
Unit
Min
DefaultMAINS FREQ. LEVEL (Mains->Frequency level)
Max
Mains Under Frequency
Hz
Hz
Hz
Hz
20.0 75.0
20.0 75.0
20.0 75.0
20.0 75.0
45.0
48.0
55.0
52.0
Mains Under Frequency Reset
Mains Over Frequency
Mains Over Frequency Reset
Under freq trip
Under freq reset
Over freq trip
Over freq reset
Unit
600
60(dis)
60
60
600
600
600
VV
VV
VV
VV
60(dis)
Min
Default
Max
Generator Under Voltage Shutdown
Generator Under Voltage Pre-Alarm
Generator Under Voltage Pre-Alarm Reset
Generator Over Voltage Shutdown
Generator Over Voltage Pre-Alarm
320
340
350
440
60(dis) 600
60 600
420
400
Generator Over Voltage Pre-Alarm Reset
VV
VV
Under volt shutdown
Under volt prealarm
Under volt reset
Over volt shutdown
Over volt prealarm
Over volt reset
Unit
Shutdown delay time
Generator Voltage Shutdown Delay Time
GENERATOR VOLT LEVEL (Generator->Volt level)
0.0 10.0 1.0
Sec
75.0
30.0(dis)
75.0
75.0
Hz
30.0(dis)
Min
Default
Max
Generator Under Frequency Pre-Alarm
Generator Under Frequency Pre-Alarm Reset
Generator Over Frequency Shutdown
Generator Over Frequency Pre-Alarm
Generator Over Frequency Pre-Alarm Reset
45.0
46.0
58.0
55.0
54.0
Generator Frequency Shutdown Delay Time
Hz
Hz
Hz
Hz
30.0
30.0(dis)
30.0
75.0
75.0
Under freq prealarm
Under freq reset
Over freq shutdown
Over freq prealarm
Over freq reset
Shutdown delay time
Unit
GENERATOR FREQ LEVEL (Generator->Frequency level)
75.0
75.0
Hz
30.0
Nominal Alternator Frequency
50.0
43.0
Hz
Nominal frequency
Under freq shutdown
Generator Under Frequency Shutdown
30.0(dis)
0.0 10.0 1.0
Sec
4.2.3 Generator
Mains Failure Detection En/Dis
Look Mains Failure at Stop Mode En/Dis
Always Look Mains Return Delay
ENABLE: The module will monitor the mains supply. If the mains supply go out side of limits, the
module will initiate its automatic mains failure sequence.
ENABLE: As soon as the module detects a mains failure the mains contactor or breaker relay will be
opened to remove the supply from the load. This is to prevent damage to the load in case of single-
phase failure.
DISABLE: In the event of a mains failure the unit will attempt to maintain the supply to the load for the
incoming AC mains supply until the generator is available to go on load. In the event of a generator
failure the module will default back to the incoming AC mains supply.
ENABLE: T
DISABLE: T
generator is available to go on load
he module will always wait the Mains Return Delay parameter before transferring the load
back to mains.
he module will wait the Mains Return Delay parameter while only the engine is running
and the before transferring the load back to mains.
Min
Default
Unit
MAINS ACTIONS (Mains->Actions)
Max
Mains Failure Detection En/Dis
Look Mains Failure at Stop Mode En/Dis
Always Look Mains Return Delay
Mains failure detect
Mains fail.stop mode
Always return delay
ENABLENABL/DISBL
ENABL/DISBL
ENABL/DISBL
ENABL
DISBL