To Next Page
J
Jonathan JenkinsSep 1, 2025
What to do if my eove EO-150 shows 'Turbine overheat'?
- LLeah MooreSep 1, 2025
Contact your service provider.
What to do if my eove EO-150 shows 'Turbine overheat'?
Contact your service provider.
What does 'High Pres Medium Priority' mean on my eove EO-150, and how do I fix it?
The 'High Pres Medium Priority' message on your eove Fan means that the inspiratory pressure is too high. Inspect the circuit for occlusion.
What to do if my eove Fan shows a 'Battery Fail' alarm?
Switch to backup ventilator (for ventilator dependent patient).
What does 'Low VTI Medium Priority' mean on my eove Fan and how to resolve it?
The 'Low VTI Medium Priority' message on your eove Fan means that the inspired tidal volume is too low. Inspect the circuit and expiratory module and check the pressure settings.
What does 'High VTI Medium Priority' mean on my eove EO-150 Fan, and how can I resolve it?
The 'High VTI Medium Priority' message on your eove Fan indicates that the inspired tidal volume is too high. Inspect the circuit and expiratory module for leaks.
What does 'Low SPO2 Medium Priority' mean on my eove EO-150 Fan, and how do I fix it?
The 'Low SPO2 Medium Priority' message on your eove Fan means that the pulse oximeter is recording low SPO2 levels. Check the patient and ensure the pulse oximeter is correctly attached.
What does 'Batt. Charge Fail Medium Priority' mean on eove EO-150 and how to resolve it?
The 'Batt. Charge Fail Medium Priority' message on your eove Fan means there is an internal charger failure. Check the level of the battery charge. If the problem persists, contact your service provider.
What does it mean when my eove Fan says battery power is low?
When the eove Fan indicates low battery power, plug the ventilator into either an AC or DC power source. You have approximately 15 minutes of guaranteed ventilation time remaining.
What to do if my eove EO-150 battery life is less than 2 hours?
If the eove Fan's battery life is less than 2 hours, plug the ventilator into an AC or DC power source. For ventilator-dependent patients, avoid using the battery as the primary power source.
What to do if the eove EO-150 indicates that the patient is obstructed?
If the eove Fan indicates a patient obstruction, it might be due to a blocked patient circuit. Check the mask or tubing for any blockages.
Key patient use parameters, contraindications, and potential adverse reactions.
Important safety guidelines for device operation and handling, including environmental considerations.
Specific safety measures for patients relying on continuous ventilation support.
Identification of front and rear panel components and connectors for the EO-150 ventilator.
Explanation of the menu bar, keyboard, symbols, and touch screen interface for operation.
Steps for powering on/off, starting, and stopping ventilation for patient use.
Guidance on navigating patient, monitoring, and clinical menus to adjust settings and preferences.
Managing ventilation presets, circuit, and patient type configurations for personalized therapy.
Guidelines for selecting, connecting, and calibrating patient circuits for optimal performance.
Instructions for attaching filters, humidifiers, sensors, and other compatible accessories.
Details on using mains, DC, and battery power, including run times and charging procedures.
Procedures for mounting the device on a trolley and using transport bags for patient mobility.
How alarms are signaled, viewed, and temporarily muted by the device.
Methods for inhibiting alarms and understanding alarm priority levels (High/Medium).
Guidance on identifying causes and necessary actions for various alarm situations.
Procedures for regular cleaning, filter replacement, and battery checks.
Recommended servicing intervals and procedures conducted by trained personnel.
Detailed information on device physical, ventilation, power, and environmental operating parameters.
Information on device emissions, immunity, and compliance with relevant safety standards.
General| Model | EO-150 |
|---|---|
| Oscillation | Yes |
| Speeds | 3 |
| Power Consumption | 45W |
| Warranty | 1 year |