Exmark NAVIGATOR - User Manual

Other manuals for Exmark NAVIGATOR

Parts Manual28 pages

Setup Instructions4 pages

Questions and Answers

S
Samantha BarnesSep 8, 2025
What causes uneven cutting height on Exmark NAVIGATOR Lawn Mower?
- A
  adam14Sep 8, 2025
  Uneven cutting height on your Exmark lawn mower may be due to: * Blade(s) not sharp. Sharpen the blade(s). * Bent cutting blade(s). Install new cutting blade(s). * Mower deck is not level. Level mower deck from side-to-side and front-to-rear. * Underside of mower is dirty. Clean the underside of the mower. * Incorrect tire pressure in drive tires. Adjust tire pressure in the drive tires. * Spacers are in wrong location. Position spacers under hairpins. * Tips of adjacent blades are at an uneven cutting height. Replace blades, spindles and (or) check for damage to mower deck.
C
charlesbautistaAug 22, 2025
Why Exmark Lawn Mower starter does not crank?
- M
  Megan HuffAug 22, 2025
  The starter might not crank due to several reasons: * The PTO might be engaged, so disengage it. * The parking brake may not be set, set the parking brake. * The speed control lever might not be in neutral, so ensure it is. * The battery may not have a full charge. In this case, charge the battery. Refer to the Check Battery Charge and Recommended Jump Starting Procedure sections in Maintenance for details. * Electrical connections might be corroded, loose, or faulty. Check the electrical connections for good contact. Clean connector terminals thoroughly with electrical contact cleaner, apply dielectric grease and reconnect. * A fuse might be blown, so replace it. * A relay or switch could be defective.
A
Adam ValentineSep 5, 2025
What to do if Exmark Lawn Mower overheats?
- D
  daniel16Sep 5, 2025
  If your Exmark lawn mower engine is overheating, check the following: * Engine load is excessive. Reduce the ground speed. * Oil level in the crankcase is low. Add oil to the crankcase. * Cooling fins and air passages for the engine are plugged. Remove the obstructions from the cooling fins and air passages.
L
Lisa JonesSep 3, 2025
Why Exmark NAVIGATOR engine loses power?
- T
  Terrance FuentesSep 4, 2025
  Your Exmark lawn mower engine might be losing power due to: * Excessive engine load. Reduce the ground speed. * A dirty air cleaner. Clean or replace the air cleaner element. * Low oil level in the crankcase. Add oil to the crankcase. * Plugged cooling fins and air passages for the engine. Remove the obstructions from the cooling fins and air passages. * A plugged fuel tank vent system. Clean or replace the plugged component. * A dirty fuel filter. Replace the fuel filter.
B
Bonnie HansenSep 2, 2025
What to do if Exmark Lawn Mower engine loses power?
- Y
  ykelleySep 2, 2025
  If your Exmark Lawn Mower engine is losing power, there are several potential causes. First, the engine load may be excessive, so reduce the ground speed. Other possible reasons include a dirty air cleaner (clean or replace it), low oil level in the crankcase (add oil), plugged cooling fins and air passages (remove obstructions), or a plugged vent hole in the fuel cap (clean or replace the cap). Also, check for a dirty fuel filter and replace it. If the issue persists and you suspect dirt, water, or stale fuel in the fuel system, it is recommended to contact an Authorized Service Dealer.
U
ucarterSep 1, 2025
Why is my Exmark NAVIGATOR engine overheating?
- M
  Micheal CardenasSep 1, 2025
  If your Exmark Lawn Mower engine is overheating, reduce the ground speed if the engine load is excessive. Also, check the oil level in the crankcase and add oil if it is low. Make sure the cooling fins and air passages are free of obstructions; if they are plugged, remove the obstructions.
T
Tiffany EsparzaAug 30, 2025
Why is my Exmark Lawn Mower engine losing power?
- C
  Charles SheppardAug 30, 2025
  If your Exmark Lawn Mower engine is losing power, first, reduce the ground speed if the engine load is excessive. Other possible causes include a dirty air cleaner (clean or replace it), low oil level in the crankcase (add oil), plugged cooling fins and air passages (remove obstructions), a plugged vent hole in the fuel cap (clean or replace the cap), or a dirty fuel filter (replace it). If the problem persists, there may be dirt, water, or stale fuel in the fuel system, in which case you should contact an Authorized Service Dealer.
R
Rebecca BryanAug 29, 2025
What to do if Exmark NAVIGATOR does not drive?
- T
  Thomas KimAug 29, 2025
  If your Exmark lawn mower does not drive, check the following: * Bypass valve is not closed tight. Tighten the bypass valve. * Drive or pump belt is worn, loose or broken. Change the belt. * Drive or pump belt is off a pulley. Change the belt. * Broken or missing idler spring. Replace the spring. * Hydraulic fluid level is low or too hot. Add hydraulic fluid to reservoir or let it cool down.
H
Heidi MasonAug 27, 2025
What to do if Exmark NAVIGATOR starter does not crank?
- D
  Doris MuellerAug 27, 2025
  If the starter on your Exmark Lawn Mower isn't cranking, make sure the PTO is disengaged and the parking brake is set. Also, check that the speed control lever is in the neutral position. A low battery charge could also be the culprit, so charge the battery. Examine the electrical connections for corrosion, looseness, or faults; clean the terminals with electrical contact cleaner, apply dielectric grease, and reconnect them. Replace any blown fuses. If the problem persists, the relay or switch may be defective, and you should contact an Authorized Service Dealer.
M
Mark HunterAug 27, 2025
What to do if my Exmark NAVIGATOR Lawn Mower starter does not crank?
- C
  Carolyn KeithAug 27, 2025
  If your Exmark Lawn Mower starter isn't cranking, make sure the PTO is disengaged and the parking brake is set. Also, ensure the speed control lever is in the neutral position. Other potential causes include a battery that needs charging (charge the battery), corroded or loose electrical connections (clean and reconnect them), a blown fuse (replace it), or a defective relay or switch (contact a service dealer).

Exmark NAVIGATOR Specifications

General

Drive System	Hydrostatic
Deck Construction	Fabricated
Transmission	Hydrostatic
Deck Material	Steel
Turning Radius	Zero-turn
Cutting Width	42 in
Blade Tip Speed	18, 500 fpm
Engine Type	V-Twin

Summary

Introduction

Read the Entire Manual

Crucial instruction to read the entire manual before operating the mower for safety and proper use.

Safety

Safety Alert Symbol

Explains the safety alert symbol used in the manual and on the machine to identify important safety messages.

Safe Operating Practices

Provides guidelines for safe operation, including training and preparation.

Slope Operation

Details safe practices for operating the mower on slopes, including angle limits and precautions.

Maintenance and Storage

Instructions for storing the machine and performing maintenance tasks safely.

Operation

Steering Levers

Details the function and operation of the steering levers for controlling machine direction and speed.

Speed Control Lever

Explains how to set and use the speed control lever for maximum forward speed and neutral.

Starting the Engine

Step-by-step procedure for safely starting the engine, including pre-start checks.

Engaging the PTO

Procedure for safely engaging the Power Take-Off (PTO) and blower drives.

Stopping the Engine

Steps to safely stop the engine and secure the machine.

Driving the Machine

Guidance on operating the machine, including forward and reverse movement and turning.

Adjusting the Cutting Height

Procedure for adjusting the mower deck to ensure proper leveling.

Removing the Deck

Step-by-step guide on how to safely remove the mower deck from the tractor.

Transporting a Unit

Guidelines for safely transporting the mower unit on a trailer or truck.

Specifications

Engine

Details engine specifications including oil type, RPM, and fuel recommendations.

Safety Interlock System

Description of the safety interlock system and its components.

Operator Controls

Overview of the steering, speed control, PTO engagement, and parking brake controls.

Dimensions

Provides overall width, length, height, and tread width specifications for different deck sizes.

Torque Requirements

Lists torque specifications for various bolts and nuts on the machine.

Maintenance

Recommended Maintenance Schedule(s)

Provides a schedule for routine maintenance tasks based on operating hours.

Check Engine Oil Level

Instructions for checking and maintaining the correct engine oil level.

Check Safety Interlock System

Steps to verify the proper functioning of all safety interlock mechanisms.

Check Hydraulic Oil Level

Procedure for checking the hydraulic oil level and adding oil if necessary.

Deck Leveling

Procedure for adjusting the mower deck to ensure proper leveling.

Parking Brake Adjustment

Steps to check and adjust the parking brake for proper engagement.

Reverse Stop Rod Adjustment

Procedure for adjusting the reverse stop rod to ensure proper lever movement.

Cleaning

General section on cleaning various parts of the machine.

Troubleshooting

Starter does not crank

Common causes and corrective actions when the starter motor fails to crank the engine.

Engine will not start, starts hard, or fails to keep running

Troubleshooting steps for engine starting difficulties or failure to maintain running.

Engine loses power

Diagnosing and resolving issues related to engine power loss.

Machine does not drive

Common reasons and fixes when the machine fails to drive.

Blades do not rotate

Common causes and corrective actions when the mower blades fail to rotate.

Schematics

Electrical Diagram All Units Except Kohler EFI

Wiring diagram for the electrical system on all units except those with Kohler EFI.

Electrical Diagram Kohler EFI

Wiring diagram for the electrical system specific to Kohler EFI units.

Hydraulic Diagram

Diagram illustrating the hydraulic system components and flow.

Exmark Commercial Turf Equipment 2 Year Limited Warranty

Conditions and Products Covered

Details the terms and conditions of the limited warranty and covered products.

Items and Conditions Not Covered

Lists exclusions from warranty coverage, such as normal wear and misuse.

Instructions for Obtaining Warranty Service

Steps to follow for obtaining warranty service, including dealer contact information.

Owners Responsibilities

Outlines the owner's responsibilities for maintaining the product and seeking warranty service.

Related product manuals

Exmark NAVIGATOR 4500-367

44 pages

Frontrunner 720,000 & Higher Serial Nos.

Exmark Lazer Z Series

76 pages

Exmark Radius X Series

84 pages

Exmark LAZER Z E Series

76 pages

Exmark LAZER Z X Series

76 pages

Exmark LAZER Z S-SERIES

64 pages

Exmark NAVIGATOR - User Manual

Table of Contents

Other manuals for Exmark NAVIGATOR

Questions and Answers

Exmark NAVIGATOR Specifications

Summary

Introduction

Read the Entire Manual

Safety

Safety Alert Symbol

Safe Operating Practices

Slope Operation

Maintenance and Storage

Operation

Steering Levers

Speed Control Lever

Starting the Engine

Engaging the PTO

Stopping the Engine

Driving the Machine

Adjusting the Cutting Height

Removing the Deck

Transporting a Unit

Specifications

Engine

Safety Interlock System

Operator Controls

Dimensions

Torque Requirements

Maintenance

Recommended Maintenance Schedule(s)

Check Engine Oil Level

Check Safety Interlock System

Check Hydraulic Oil Level

Deck Leveling

Parking Brake Adjustment

Reverse Stop Rod Adjustment

Cleaning

Troubleshooting

Starter does not crank

Engine will not start, starts hard, or fails to keep running

Engine loses power

Machine does not drive

Blades do not rotate

Schematics

Electrical Diagram All Units Except Kohler EFI

Electrical Diagram Kohler EFI

Hydraulic Diagram

Exmark Commercial Turf Equipment 2 Year Limited Warranty

Conditions and Products Covered

Items and Conditions Not Covered

Instructions for Obtaining Warranty Service

Owners Responsibilities

Related product manuals