Extron electronics IN1804 Series - Page 84

IN1804 Seamless Scaling Switchers • SIS Configuration and Control 76
Command ASCII Command
(Host to Switcher)
Response
(Switcher to Host)
Additional Description
Advanced Configuration (continued)
Contact Port Status
View individual contact port
status
EX7%
CNTC
} X7^]
Verbose modes 2 and 3:
Cntc
X7%
*
X7^]
View the contact status
X7^
of contact
port
X7%
.
View status of all contact
ports
E
CNTC
} X7^
•...
X7^]
View status
X7^
of all contact ports.
Tally Port Status
Set individual port state
EX7%
*
X7^
TALY
}
Taly
X7%
*
X7^]
Set the tally output state for port
X7%
to
X7^
.
Set states of all ports
EX7^
...
X7^
TALY
}
Set all tally ports at once to port state
X7^
.
Taly
X7^
...
X7^]
View individual tally port
status
EX7%
TALY
} X7^]
View the tally status
X7^
of contact port
X7%
.
View status of all tally ports
E
TALY
} X7^
•...
X7^]
View status
X7^
of all tally ports.
KEY:
X7%
= Contact/Tally port number
1 through 7
X7^
= Contact/Tally port state
0 = Open, 1 = Closed
Twisted Pair Protocol
Set input TP protocol
(IN1804 DI and DI/DO only)
E
I4*
X6&
HDBT
}
HdbtI4*
X6&]
Set the TP protocol for input 4 to
X6&
.
View input TP protocol
E
I4HDBT
} X6&]
View current TP protocol setting for input
4.
Set output TP protocol
(IN1804 DO and DI/DO only)
E
O1*
X6&
HDBT
}
HdbtO1*
X6&]
Set the TP protocol for output 1A to
X6&
.
View output TP protocol
E
O1HDBT
} X6&]
View current TP protocol setting for
output 1A.
DTP Remote Power Parameters
ATTENTION:
• Ensure that the correct remote DTP power setting is used. Sending DTP2 power to a DTP (series 1) endpoint can
result in hardware damage. Enable DTP2 power only to a compatible DTP2 endpoint.
• Assurez-vous de bien régler l’alimentation DTP à distance. L’envoi d’une alimentation DTP2 à un point de connexion
DTP (ancienne gamme) peut provoquer des dommages matériels. Assurez une alimentation DTP2 uniquement vers un
point de connexion DTP2 compatible
Set input remote power
(IN1804 DI and DI/DO only)
E
I4*
X6^
RPWR
}
RpwrI4*
X6^]
Set the remote power on input 4 to
X6^
.
View input remote power
E
I4RPWR
} X6^]
View remote power setting for input 4.
Set output remote power
(IN1804 DO and DI/DO only)
E
O1*
X6^
RPWR
}
RpwrO1*
X6^]
Set the remote power for output 1A to
X6^
.
View output remote power
E
O1RPWR
} X6^]
View remote power setting for output 1A.
KEY:
X6^
= DTP remote power status
0 = No remote power (default)
1 = DTP
2 = DTP2
X6&
= DTP protocol setting
0 = DTP format (default), 1 = XTP format, 2 = HDBaseT format