FAAC B680H - Page 34

6
J6
J12
J13
J5
J10
J11
J14
J7
+
-
F
SW1 SW2 SW3
J15
J1 J2 J3 J4
M2
M1A
M1
DL1 DL2
DL10
DL11
DL12
DL13 DL14
DL18 DL17
DL7 DL5
DL8
DL6
DL9
DL16
DL3
DL4
DL15
2Easy BUS
OPEN
CLOSE
FSW
STOP
ALARM
GND
+24
3 4 5
6
7
8 9 10 11 12 13 14 15 16 17 18 19 20 21
22 23 2
2
+24
+24 +24 +24
OUT1
OUT2
OUT3
Relay NO Relay NC
GND
LAMP
LOOP 1
LOOP 2
MOTOR
POWER
SUPPLY
BATTERY
ENCODER
DISP1
M
SW4
1 2
2 24 5 6
7
Fig.1
ENGLISH
E680 CONTROL BOARD
DISP1 Signalling/Programmingdisplay
DL1 BUSDevicestatus
DL2 BUSstatus(seeparagraph5.3)
DL3 LOOP1status
DL4 LOOP2status
DL5 Boardfailuresignal
DL6 Not used
DL7 Encoderstatus
DL8 Not used
DL9 Boardpowersupplypresent
DL10..DL14 InputsstatusLEDs(seeparagraph4.1)
DL15 Releasedbarsignal
DL16 Batterypowersignal
DL17 Radiochannel1activity
DL18 Radiochannel2activity
J1 Inputsignalconnector
J2 Digitaloutputconnector
J3 Signallinglampconnector
J4 Detection loop connector
J5 Motor connector
J6 BUS2Easyconnector
J7 Beam movement encoder connector
J10 Decoder / Minidec / RP-RP2 radio board connector
J11 Released bar detection connector
J12 Emergencybatteryconnector
J13 Continuouspowervoltageconnector
J14 USBconnectorforfirmwareupgrade
J15 Integratedflashing
trafficlightconnector
F Programmingkey“F”
+ Programmingkey“+”
- Programmingkey“-”
SW4 Programmingkey“SETUP”
M1/M1A/M2 Optionalmoduleconnector(Connectivity):
1. WARNINGS
Warning - Before carrying out any workon the control board
(connections,maintenance,etc.)always:
• cutofftheelectricalpower;
• install a differentialmagnetothermic switch witha suitable
activationthresholdupstreamfromthesystem;
• alwaysseparatethepowercablesfromthecontrolandsafety
cables(button,receiver,photocells,etc.);
• avoidanyelectricaldisturbance using separate sheaths or a
shieldedcable(withtheshieldconnectedtotheearth).
2. DESCRIPTION OF THE COMPONENTS
Mains
power
voltage
90-240 V~ +6% -10%
connected to
switchingpowersupply
Continuous
power voltage
36 V
"
Absorbed power 270W
Accessories
power supply
24 V
"
Max accessories
current
800 mA
Operating ambient
temperature
from-20°Cto+55°C
Protection fuses 4self-restoring
3. TECHNICAL SPECIFICATIONS
Pause time Programmable(from 0 seconds to 4.1
minutes)
Work time
Programmable(from0to4minutes)
Motor power Programmableon50levels
Motor speed Programmableon10levels
Programmability 3 configuration levels for greater flexibility
ofuse
Rapid connector 1 5-pin connectorforMinidecradio board,
Decoder,RP/RP2
Programmable
outputs
4 programmable outputs in 19 different
functions
Specifications
Deceleration management, encoder,
multi-functiondisplay,BUStechnology
andBUILT-INMETALMASS DETECTOR,
USBconnectorforfirmwareupgrade