FAAC B680H - Page 33

5
ENGLISH
9. REVERSING THE OPENING DIRECTION
Theopeningdirectionofthebarrierisusuallydeterminedatthetime
ofinstallationwiththeinstallationofthespringguide,thespringand
thepreloadadjustmentringnutonthepistonlocatedonthebeam
downward travel side.
Shoulditbenecessarytochangetheopeningdirection,proceedas
follows:
•
Releasetheoperator,asshowninparagraph6,andplacethe
beaminverticalposition,thenlocktheoperatoragain.
• RemovethebeamasshowninFig.17.
• Removethedevicesecuringtheplungingpistontotherocker
arm,asshowninFig.13.
• Loosenthepre-load ring nut completely, removeitandthen
removethebalancingspringandspring guide, reversing the
orderdescribedinparagraph4.4andinFig.14regardingthe
mechanicalinstallationoftheautomatedsystem.
• Refittheplungingpistoninthecorrectfixinghole.
• Proceedtoremovethefixingscrewonthepistonontheopposite
side.
•
Releasetheautomatedsystem,turntherockerarm90°andre-
insert,inorder,thespringguide,thebalancingspringandthe
theringnutintheplungingpistoninstalledonthenewclosing
side,accordingtotheorderdescribedinFig.14.Oncethisis
done,refittheplungingpistonontherockerarm.
• ReinstallthebarfollowingtheinstructionsinFig.17.
• Balancethesystemonceagainfollowingtheproceduredescribed
inparagraphs4.5and4.6.
• Lock the operator once again following the instructions in
paragraph7
• Reverse the motor cable connection as shown in point d
of Fig. 14
10. ACCESSORIES
10.1 Installing a photocell
Thebarrierisequippedwithalateralcoveringprofile(fittedinthe
compartmentopening)under whichthereare holesforcontaining
Safebeam,BUSorwirelessphotocells.
Toinstallthephotocells,proceedasfollows:
1. Remove the barrier compartment.
2. Match the holes on the barrier compartment with the holes on
thecorrespondingaluminiumcoveringprofileonthephotocell
installation side; ref. a isusedtofixthedevice,ref.bisused
forthepassageoftheitspowercable.Determinetheholesize
accordingtothesizeofthecablesandofthefixingscrewsused.
3. Connectthephotocellfollowingtheprovideddiagram.
4. Fixthephotocelltothelateralprofile,asshowninFig.22.
10.2 Installing the bar light kit
InstallationofanLEDbarlightkitincreasesvisibilityofthebar.
ProceedtoinstallfollowingtheinstructionscontainedinFig.31and
securingtheconnectioncableaccordingtothepathshown,usingthe
openingsforinsertingthetiestraps,locatedontheupright.
ConnectthekittooutputOut4ontheelectronicboardandconfigure
itaccordingtotheavailableswitchingonmodes(refertothesection
regardingtheelectronicboard,paragraph6onpage12).
Ensure that the two connector jacks are actually in
contact with the conductors inside the cord. Should
the bar lights still not turn on, reverse the connection
polarity.
10.3 Installation of a receiver antenna
Incaseareceiverantennashouldneedtobeattachedtothebarrier,
itcanbesecuredtotheflashingintegratedtrafficlightconnector(or
totheplasticbracket,iftheoptionalflashingtrafficlightconnector
shouldnothavebeeninstalled),asindicatedinthediagramsinFig.32.
11. REPAIRS
Forrepairs,contactanauthorisedFAACServiceCentre.