FAAC B680H - Page 41

13
ENGLISH
Display
Function
Default
P1
Output 1 Polarity
Allowssettingoftheoutputpolarity:
Y outputNC
no outputNO
NOTE:iftheoutputsettingis00 (Failsafe),
keepthevaluesettono
no
o2
Output 2
Output2signaltype,see“Output 1”
03
P2
Output 2 Polarity
Output 2 polarity,see parameter regarding
“Output 1 Polarity”
no
o3
Output 3
Output3signaltype,see“Output 1”
19
P3
Output 3 Polarity
Output 3 polarity,see parameter regarding
“Output 1 Polarity”
no
o4
Output 4
Output4signaltype,see“Output 1”
01
P4
Output 4 Polarity
Output 4 polarity,see parameter regarding
“Output 1 Polarity”
no
o5
Integrated flashing lamp operating mode
Letsyouchoosebetweentwooperatingmodes
fortheintegrated flashing lamp (if present)
connectedtooutputJ15.
01 “Trafc light” mode (steady green
when paused/open, ashing red when
moving,steadyredwhenclosed)
02 ”Flashing lamp” mode (ashing red
when bar is moving, off in all other
cases)
01
AS
Service request (linked to the following
two functions):
If activated, at the end of the countdown
(whichcanbesetwiththetwofollowing“Cycle
Programming”functions)itactivatestheLAMP
outputfor4secevery30sec(servicerequest).
It can be useful for setting programmed
maintenance work.
Y Active
no Disabled
no
nc
Cycle programming in thousands:
Is used to set a countdown of the system
operation cycles; the value can be set from
0 to 99 (thousands of cycles). The value
displayed is updated with the succession of
the cycles, interacting with the value of nC
(99 decrements of nc correspond to 1
decrement of
nC).
Thefunctioncanbeused,togetherwithnC,
toverifytheuseofthesystemandforuseof
“ServiceRequest”.
00
Display
Function
Default
nC
Cycle programming in hundreds of
thousands:
Is used to set a countdown of the system
operationcycles;thevaluecanbesetfrom0
to99(hundredsof thousandsofcycles).The
valuedisplayedisupdatedwiththesuccession
of the cycles, interacting with the value of
nc.(1decrementofnC corresponds to 99
decrements of
nc).
Thefunctioncanbeused,togetherwithnc,
toverifytheuseofthesystemandforuseof
“ServiceRequest”.
01
St
AUTOMATED SYSTEM STATUS:
Thisallowsyoutochoosewhethertoquittheprogramme
and save the data.
Y=quitandsavethedata
no=quitwithoutsavingthedata
Onquittingtheprogramme,presstheFkeytodisplay
againthestatusoftheautomatedsystem.
You can go to St at any time by simultaneously
pressing F and -
6.1 Conguring the loop detector
TheE680boardfeaturesanintegratedmetalmassdetectorforthe
inductiondetectionofvehicles.
6.1.1 Specications:
• Galvanic separation between the detector electronics and the
loop electronics
•
Automaticalignmentofthesystemimmediately following
activation
•
Continuousresettingofthefrequencydrifts
• Sensitivityindependentofloopinductivity
• Adjustmentoftheloopworkfrequencywithautomaticselection
• OccupiedloopmessagewithLEDdisplay
• LoopstatusaddressableonoutputsOUT1,OUT2,OUT3and
OUT 4
6.1.2 Connection:
Connectthedetectionloops according to the layout on page 7,
Fig.2
-Terminals24-25forLOOP1=loopwithgateopeningfunction;
-Terminals26-27forLOOP2=loopwithclosingand/orsafety
whenclosingfunction.
Formoreinformationontheeffectoftheloopsignalsontheautomated
system, refer to the logics tables in paragraph 10 “OPERATING
LOGICSTABLE”.
To enable the functionality of the connected loops, enter Basic
congurationmodeandsetparametersL1 and L2 on Yconsistently
withthe number and type of connected loops.If only one loop is
installed,enableonlythecorrespondingprogrammingstep.
TheloopdetectoroperatingstatusisindicatedbytheDL3andDL4
statusLEDs.