FAAC B680H - Page 43

15
ENGLISH
04
Activation of DEAD-MAN opening (command always pressed). Releasing the OPEN
command will stop operation
Y = active
no = disabled
05
Whenthisfunctionisactivated,theOPEN commandduringopeningwillstopmovement.
If parameter 06 is nothesystemisreadyforopening.
If parameter 06 is Ythesystemisreadyforclosing.
Y=whenopeningitstops
no = disabled
06
Whenthisfunctionisactivated,theOPEN commandduringopeningreversesmovement.
If parameters 05 and 06 are noOPENwillhavenoeffectduringopening.
Y=whenopeningitreverses
no = disabled
07
Whenthisfunctionisactivated,theOPEN commandduringpausestopsoperation.
If parameters 07 and 08 are noOPENresetsthepausetime
Y=wheninpauseitstops
no = disabled
08
Whenthisfunctionisactivated,theOPEN commandduringpausecausesclosing.
If parameters 07 and 08 are noOPENresetsthepausetime.
Y =wheninpauseitcloses
no = disabled
09
When this function is activated, the OPEN command during closing stops operation,
otherwise it reverses movement.
Y = stops
no = reverses
10
Activation of DEAD-MAN closing (command always pressed). Releasing the CLOSE
command will stop operation
Y = active
no = disabled
11
Whenthisfunctionisactivated,theCLOSE commandhaspriorityoverOPEN,otherwise
OPENhaspriorityoverCLOSE.
Y = active
no = disabled
12
Whenthisfunctionisactivated,theCLOSE commandcommandsclosingwhenreleased.
AslongasCLOSEisactivated,theunitstaysinclosingpre-ashing.
Y = closes when released
no=closesimmediately
13
Whenthis functionis activated,the CLOSE commandduring openingstops operation,
otherwisetheCLOSEcommandcommandsreverseimmediatelyorwhenopeningiscom-
pleted(seealsoparameter14)
Y = CLOSE stops
no = CLOSE reverses
14
When this function is activated, and if parameter 13 is no, the CLOSE command
commandsimmediateclosingattheendoftheopeningcycle(storesCLOSE).Ifparameters
13 and 14 are noCLOSEcommandsimmediateclosing.
Y = closes at the end of
opening
no=immediateclosing
15
When this function is activated, with the system blocked by a STOP, a next OPEN
moves in the opposite direction. If parameter
15 is noitalwayscloses.
Y = moves in the opposite
direction
no=alwayscloses
16
Whenthis function isactivated, during closing,the CLOSING SAFETIES stop and allow
motiontoresumewhentheyaredisengaged,otherwisetheyimmediatelyreverseopening.
Y=closeswhendisengaged
no = immediate reverse
17
Whenthisfunctionisactivated,theCLOSING SAFETIEScommandclosingwhentheyare
disengaged(seealsoparameter18).
Y = closing when FSW
isdisengaged
no = disabled
18
When this function is activated, and if parameter 17 is Y, the unit will wait for the
opening cycle to end before executing the closing command provided by the
CLOSING SAFETIES.
Y = closes at the end of
opening
no = disabled
19
Whenthisfunctionisactivated,duringclosing,LOOP2stopsandallowsmotiontoresume
whenitisdisengaged,otherwiseitimmediatelyreversesopening.
Y=closeswhendisengaged
no = immediate reverse
20
Whenthisfunctionisactivated,LOOP2commandsclosingwhenitisdisengaged(seealso
parameter 21).
Y = closes if LOOP2 is clear
no = disabled
21
Whenthisfunctionisactivated,andifparameter21 is Y,theunitwillwaitfortheopening
cycletoendbeforeexecutingtheclosingcommandprovidedbyLOOP2.
Y = closes at the end of
opening
no = disabled
22
When this function is activated: incase of a blackout, once electricalpower has been
restored,ifanOPENcommandisnotactivetheautomatedsystemreclosesimmediately.
Y = active
no = disabled
23
LOOP 1commandsopeningand,oncecompleted,itclosesifdisengaged(usefulincase
ofvehiclebacking-upwithconsecutiveloops).Ifdisabled,whenLOOP1isdisengaged,it
does not close.
Y = closes if LOOP1 clear
no = disabled
24
When this function is activated, an open or close command is only carried out after
the safeties have been disengaged.
Y = active
no = disabled
25
A.D.M.A.P. function
Whenthisfunctionisactivated,theresultisoperationofsafeties compliant with French
regulations.
Y = active
no = disabled