FAAC B680H - Putting into Service

18
J6
J12
J13
J11
J14
J7
+
-
F
Sw1
Sw2
Sw3
J15
J1 J2 J3 J4
M1
DL1
DL2
DL10
DL11
DL12
DL13
DL14
DL18
DL17
DL7
DL5
DL8
DL6
DL9
DL16
DL3
DL4
DL15
2Easy BUS
OPEN
CLOSE
FSW
STOP
ALARM
GND
+24
1
2
3
4
5
6
7
8
9
1
0
1
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
1
9
2
0
2
1
2
2
2
3
1
8
1
9
2
0
2
1
+24
+24
+24
+24
OUT1
OUT2
OUT3
Rel
ay NO
Rel
ay NC
GND
LAMP
LOOP 1
LOOP 2
BATTERY
ENCODER
DISP1
Fig.4
ENGLISH
6.4 “Expert” default parameters
Thefollowingtablecontainsthepre-definedsettingsthatcharacterize
thevariousoperationlogics.
Step. A A1 E P PA Cn Ca C
01
Y Y N N Y N Y N
02
N N N Y Y Y Y Y
03
N N N N N N N N
04
N N N N N N N Y
05
N N Y N N N N N
06
N N Y N N N N N
07
N N N N N N N N
08
N N N N N N N N
09
N N N N N N N N
10
N N N N N N N Y
11
N N N N N N N N
12
N N N Y Y N N N
13
N N N N N N N N
14
N N N Y Y Y Y N
15
N N N N N N N N
16
N N N Y Y N N N
17
N Y N N N N N N
18
N Y N N N N N N
19
N N N Y Y N N N
20
N Y N Y Y Y Y N
21
N Y N Y Y Y Y N
22
N N N N N N N N
23
N N N Y Y N N N
24
N N N N N N N N
25
N N N N N N N N
26
N N N N N N N N
27
N N N N N N N N
28
N N N N N N N N
29
N N N N N N N N
30
N N N N N Y Y N
7. START-UP
7.1 Verifying the diagnostic LEDs
Beforestartinguptheboard,itisnecessarytoverifythatthestatus
ofthediagnosticLEDscorrespondstothelogic.Saidstatusmust
coincidewiththeindicationsinFig.4,situationwhichreflectsthatof
an automated system that is CLOSED and ready to open.
The FSW, STOP and ALARM LEDs are safety inputs with
NC contacts, therefore the related LEDs must be ON
when the automated system is at rest, and go off when
the device connected is engaged.
The OPEN and CLOSE inputs are NO contact inputs,
therefore the related LEDs must be OFF when the
automated system is at rest, and go on when the device
connected is active.
The BUS status must correspond to DL2 (green) on xed
and DL1 (red) off. The BUS menu of the
Basic conguration must display the
indication shown to the side conrming
the fact that there are no engaged
photocells or active pulse generators.
7.2 Setup
Beforebeing put into operation, theE680board requires a setup
procedureduringwhichtheautomatedsystemdeterminestherotation
angleofthebeamandconsequentlyitstravel.Thesemeasurements
allowcorrectmanagementofmotordecelerationsandacceleration
ramps.
At rst start-up the board will signal the need for a setup
cycle, by displaying a ashing S0.
Forsetup,proceedasfollows:
• Usingtheparameter“Mt”inBasicconfigurationmode,checkthat
theopening/closingmovementcorrespondstothepressedkey
(+/-);ifnot,gotothemotorwiringandreversethetwoconductors
L1andL3,asshowninFig.14,Ref.d
•
Place the automated system in closing position using the
parameter“Mt”inBasicconfigurationmodeorusingtherelease
device,asshowninparagraphs6and7onpage4.
• PressandholdSW4 (“SETUP” programming key) until the
automatedsystembeginsaslowopeningmovement.Onthe
displayS1willflashindicatingthestartoftheprocedure.
• Oncethemaximumopeningpositionisreached,theautomated
systemwillstopautomatically.
• Next, the automated system will start the beam closing
movement.ThedisplaywillflashtheindicationS3.
•
Oncetheclosingpositionhas been reached, the automated
systemwillstopautomaticallyandthedisplaywillgobackto
showingtheindicationofthecurrentstatusoftheautomated
system(00 - closed).
8. TESTING THE AUTOMATED SYSTEM
Onceprogrammingiscompleted,ensurethatthesystemisoperating
correctly.
Verifyespeciallythecorrectregulationoftheautomatedsystempower
andcorrectoperationofthesafetydevicesitisconnectedtoandverify
thattheautomatedsystemconformstocurrentsafetystandards.