EasyManua.ls Logo

FAAC B680H - Page 45

FAAC B680H
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
17
ENGLISH
h1
LOOP 1 holding time
Isusedtosetpresencetimeonloop1.Whenthistimehaselapsed,theboardwillself-
calibrateandsignal“loopclear”(LEDDL3off).Whentheboardisturnedon,anautomatic
resetiscarriedout.
Y 5minutes
no innite
no
h2
LOOP 2 holding time
Isusedtosetpresencetimeonloop2.Whenthistimehaselapsed,theboardwillself-
calibrateandsignal“loopclear”(LEDDL4off).Whentheboardisturnedon,anautomatic
resetiscarriedout.
Y 5minutes
no innite
no
H1
Loop 1 articulated lorry function
Thisfunctionletsyouincreasethelevelofsensitivityatthetimeofdetection,toallowcorrect
detectionevenincaseofverytallvehiclesorduringthetransitofatractorandtrailer.
Y enabled
no disabled
Y
H2
Loop 2 articulated lorry function
Thisfunctionletsyouincreasethelevelofsensitivityatthetimeofdetection,toallowcorrect
detectionevenincaseofverytallvehiclesorduringthetransitofatractorandtrailer.
Y enabled
no disabled
Y
t
Work time (time-out)
Maximumworktimeoftheautomatedsystembeforethemotorstops,iftheopenorclose
positionisnotreached.ThevaluecanbesetfromO to 59sec.inonesecondsteps.Next,
thedisplaychangestominutesandtenthsofasecond(separatedbyadecimalpoint)and
timeisadjustedin10-secondstepsuptothemaximumvalueof4.1minutes.
30
St
STATUS OF THE AUTOMATED SYSTEM:
Exitfromprogramming,storageofdataandautomatedsystemstatusdisplay.
6.3 Pre-Dened Parameter Sets
Thetablebelowshows,foreachsetofpre-definedparameters,the
valuesthattheywillloadintheboardmemory.
Basic Configuration
dF
01 02 03 04 05 06
At
01 02 03 04 05 06
bu
LO
E E E E E E
PA
20 20 20 20 20 20
So
10 10 10 10 10 10
Sc
10 05 05 04 02 02
L1
no no no no no no
L2
no no no no no no
S1
05 05 05 05 05 05
S2
05 05 05 05 05 05
Advanced Configuration
Thefollowingtableshows,foreachsetofpre-definedparameters,
thevalues thattheywillloadintheboardmemory,in advanced
configuration.
dF
01 02 03 04 05 06
FO
25 25 30 28 30 40
FC
25 25 30 28 30 40
PF
no no no no no no
tP
00 00 00 00 00 00
oc
35 35 38 32 32 32
FS
no no no no no no
o1
00 00 00 00 00 00
P1
no no no no no no
o2
03 03 03 03 03 03
P2
no no no no no no
o3
01 01 01 01 01 01
P3
no no no no no no
o4
02 02 02 02 02 02
P4
no no no no no no
o5
01 01 01 01 01 01
AS
no no no no no no
nc
00 00 00 00 00 00
nC
00 00 00 00 00 00

Table of Contents