Fronius AB Profinet RT

Adress Description Read Write Group Unit Type Factor

E0D4 Downslope time [dSL] True True TIG / HAP s Word 0,01

ATTENTION: there are two

diﬀ erent values for 2-step and

4-step, so change GUNMODE

before changing this value

E0DF Multiplicator for TIG-STS2: True True TIG % Word 1

0...100% means Ie...Ih

E068 Actual weldingtime True False Real Values s Word 0,1

E069 Puls-synchron sliding window True False Real Values A Integer 0,1

for TIG-current

E06A Puls-synchron sliding window True False Real Values V Integer 0,01

for TIG-voltage

E06B Current at end of puls True False Real Values A Integer 0,1

E06C Voltage at end of puls True False Real Values V Integer 0,01

E06D Current at end of ground-phase True False Real Values A Integer 0,1

E06E Voltage at end of ground-phase True False Real Values V Integer 0,01

E06F Realvalue arclength True False Real Values V Integer 0,01

E070 Realvalue voltage True False Real Values V Integer 0,01

E071 Realvalue current True False Real Values A Integer 0,1

E079 Current-meanvalue of neg. wave True False Real Values A Integer 0,1

E07A Voltage-meanvalue of neg. wave True False Real Values V Integer 0,01

E0BF Realvalue gas True False Real Values ml Integer 1

E072 Min. Feeder-value True False Limits m/min Integer 0,01

E073 Max. Feeder-value True False Limits m/min Integer 0,01

E074 Min. Voltage-commandvalue True False Limits V Integer 0,01

E075 Max. Voltage-commandvalue True False Limits V Integer 0,01

E076 Min. Current-commandvalue True False Limits A Integer 0,1

E077 Max. Current-commandvalue True False Limits A Integer 0,1

E0A9 Min. Eld-value True False Limits mm Word 0,1

E0AA Max. Eld-value True False Limits mm Word 0,1

E07B Feeder creep speed True True MigMag ManSTD m/min Integer 0,01

E07C Ignition current True True MigMag ManSTD A Integer 0,1

E07D Ignition current time True True MigMag ManSTD ms Word 0,01

E07E Wirefeed speed True True MigMag ManSTD m/min Integer 0,01

E07F Background current True True MigMag ManSTD A Integer 0,1

E080 Voltage command value True True MigMag ManSTD V Integer 0,01

E081 Characteristic slope True True MigMag ManSTD µOhm Word 1

E082 Special dynamic True True MigMag ManSTD Word 1

E083 Current decrease True True MigMag ManSTD Word 1

E084 Current rise True True MigMag ManSTD Word 1

E085 Burn back time True True MigMag ManSTD s Word 0,01

E086 Burn back pulse time True True MigMag ManSTD ms Word 0,01

E087 Burn back pulsing current True True MigMag ManSTD A Integer 0,1

E088 Feeder creep speed True True MigMag ManPULS m/min Integer 0,01

E089 Ignition current True True MigMag ManPULS A Integer 0,1

E08A Ignition current time True True MigMag ManPULS ms Word 0,01

E08B Base current True True MigMag ManPULS A Integer 0,1

E08C Current rise True True MigMag ManPULS A/ms Word 0,1

Fronius AB Profinet RT - Page 214

Table of Contents