EasyManua.ls Logo

Frymaster OCF30E - User Manual

Frymaster OCF30E
68 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Frymaster, a member of the Commercial Food Equipment Service Association, recommends using
CFESA Certified Technicians.
24-Hour Service Hotline 1-800-551-8633
06
/
2018
www.frymaster.com
E-mail: fryservice@welbilt.com
*8196686*
Oil Conserving Fryer (OCF30)
™
Electric Series Fryers
Service & Parts Manual

Table of Contents

Questions and Answers

  • A
    Allen ConleyAug 7, 2025
    What to do if my Frymaster Fryer displays 'SERVICE REQUIRED – ATO BOARD'?
    • R
      Rachel HernandezAug 7, 2025
      If your Frymaster Fryer's controller displays 'SERVICE REQUIRED – ATO BOARD', first, check the fuse on the right side of the ATO box to ensure it is secure and in good condition. Also, if the controller above the ATO box lacks power, inspect the fuse below the component box. Next, with the controller turned OFF, press the TEMP button to see if the ATO software version appears. If it doesn't, the connection between the ATO and the controller might be faulty. Ensure the 6-pin CAN connectors are tightly secured between the controller (J6 and J7) and the ATO (J9 or J10) boards. Finally, check that there is correct voltage to the ATO transformer. Restore power to the board and clear any service required errors.
  • G
    Gregory OsborneAug 11, 2025
    What to do if my Frymaster OCF30E Fryer controller displays 'TOPOFF OIL EMPTY / CONFIRM'?
    • J
      johnhamiltonAug 11, 2025
      If the controller on your Frymaster Fryer displays 'TOPOFF OIL EMPTY / CONFIRM', simply fill the top off system with oil and then press the ? (CONFIRM) button.
  • M
    Manuel BrownAug 15, 2025
    Why is one vat not topping off in my Frymaster Fryer?
    • G
      Gene RojasAug 15, 2025
      If one vat on your Frymaster Fryer is not topping off, a filter error may exist. Ensure you properly clear any filter errors. Alternatively, there might be an issue with the ATO pump, loose wire connections, the RTD, or the ATO board itself. Check the ATO pump, wire connections, RTD and ATO board.
  • B
    Brandon MaynardAug 20, 2025
    What to do if one vat tops off but other vats fail to top off on my Frymaster OCF30E?
    • K
      Katie JosephAug 20, 2025
      If one vat of your Frymaster Fryer tops off, but the others don't, the solenoid on the vats that are not topping off may have failed. Check the power to the pump. If the pump is hot, the solenoid has probably failed. Also, make sure all wiring harnesses are securely connected to the ATO board and solenoids.
  • J
    Jessica RobertsAug 25, 2025
    Why is my Frymaster OCF30E Fryer topping off the incorrect vat?
    • C
      Chase HernandezAug 25, 2025
      If your Frymaster Fryer is topping off the incorrect vat, first, ensure that all the wires are correctly wired. Then, check if the flexlines are connected to the wrong vat and switch them to the correct vat if necessary.
  • V
    Valerie JensenAug 29, 2025
    How to troubleshoot no power to ATO board on Frymaster OCF30E Fryer?
    • H
      Haley PenningtonAug 29, 2025
      If there is no power to the ATO board of your Frymaster Fryer, check to ensure J5 on the front of the ATO board is fully locked into the connector. Also, verify that the fuse below the right control box and the fuse on the right side of the ATO box are not blown. Finally, check that proper voltage is present at the transformer.
  • C
    Cory WestDec 3, 2025
    Why won't the frypots top off in my Frymaster OCF30E Fryer?

    Frymaster OCF30E Specifications

    General IconGeneral
    ModelOCF30E
    Frypot Capacity30 lbs
    Voltage208/240V
    Phase1
    Power6.0/6.0 kW
    Tank Capacity30 lbs
    Oil Capacity30 lbs
    Temperature Range200°F - 375°F
    TypeElectric, Open Fryer

    Related product manuals