FUTABA FX40 - Page 125

125
<Data>
EXP1 curve adjustment
Rate A and Rate B can be adjusted separately
or simultaneously. The EXP curves rate (EXP
A, EXP B) can also be adjusted separately or
simultaneously.
>6HWWLQJPRGHV@
*[Separate] mode:5DWHVDUHDGMXVWHG
separately.
*[Combined] mode:5DWHVDUHDGMXVWHG
simultaneously.
>6HWWLQJPHWKRG@
1. Select the setting mode.
2. Touch the button of the rate or EXP curve
rate your want to set.
8VHWKHDGMXVWPHQWEXWWRQVWRVHWWKHUDWH
*Initial value: +100.0% (rate), +0.0 (EXP rate)
The curve can also be horizontally offset in the
vertical direction.
>2IIVHWWLQJWKHFXUYHKRUL]RQWDOO\LQWKHYHUWLFDO
GLUHFWLRQ@
7RXFKWKH2IIVHWEXWWRQ
8VHWKHDGMXVWPHQWEXWWRQVWRPRYHWKH
FXUYHKRUL]RQWDOO\XSRUGRZQ
*Initial value: +0.0
(EXP1 curve)
ŏ8VLQJWKH(;3FXUYHLVKHOSIXOLQ
smoothening starting of the ailerons,
elevators, rudder, etc.
(EXP2 curve)
ŏ8VLQJWKH(;3FXUYHLVKHOSIXOLQHQJLQH
rise and other engine control.
VTR curve adjustment
Rate A and Rate B can be adjusted separately or
simultaneously. The VTR curve point positions (P.
Pos. A, P. Pos. B) and rates (P. Rate A, P. Rate B)
can also be adjusted separately or simultaneously.
>6HWWLQJPRGHV@
*[Separate] mode: Positions and rates are
DGMXVWHGVHSDUDWHO\
*[Combined] mode: Positions and rates are
DGMXVWHGVLPXOWDQHRXVO\
>6HWWLQJPHWKRG@
1. Select the setting mode.
2. Touch the button of the rate or VTR curve
point position (or rate) you want to set.
8VHWKHDGMXVWPHQWEXWWRQVWRVHWWKH975
curve point position (or rate).
,QLWLDOYDOXHV5DWH33RV$
33RV%35DWH
The curve can also be offset horizontally in the
vertical direction.
>2IIVHWWLQJWKHFXUYHKRUL]RQWDOO\LQWKHYHUWLFDO
GLUHFWLRQ@
7RXFKWKH2IIVHWEXWWRQ
8VHWKHDGMXVWPHQWEXWWRQVWRPRYHWKH
FXUYHKRUL]RQWDOO\XSDQGGRZQZLWKWKH
DGMXVWPHQWEXWWRQV
*Initial value: +0.0%
(VTR curve)
ŏ6HWWLQJLVIDVWLIOHIWULJKWXSDQGGRZQ
DUHÀUVWGHFLGHGLQWKH&RPELQHGPRGH
and the mode is then switched to the
Separate mode.
When this curve is used when the control
surface angle is large such as with
acrobatic models, switching from normal
flight to acrobatic is performed without
switch operation.