GE F60 - Page 725

GE Multilin F60 Feeder Protection System iii
INDEX
DIGITAL ELEMENTS
application example..................................................... 5-254
FlexLogic operands ..................................................... 5-149
logic............................................................................ 5-253
Modbus registers...........................................................B-50
settings ....................................................................... 5-252
DIGITAL OUTPUTS
see entry for CONTACT OUTPUTS
DIMENSIONS ............................................................. 3-1, 3-2
DIRECT DEVICES
actual values ................................................................. 6-10
Modbus registers...........................................................B-26
settings ....................................................................... 5-297
DIRECT I/O
see also DIRECT INPUTS and DIRECT OUTPUTS
application example...........................................5-298, 5-299
configuration examples ........................ 5-92, 5-94, 5-97, 5-98
settings ............................................. 5-92, 5-97, 5-98, 5-297
DIRECT INPUTS
actual values ................................................................... 6-9
application example...........................................5-298, 5-299
clearing counters............................................................. 7-2
FlexLogic operands ..................................................... 5-154
Modbus registers.......................B-14, B-15, B-26, B-68, B-69
settings ....................................................................... 5-297
specifications ................................................................ 2-26
DIRECT INPUTS/OUTPUTS
error messages ............................................................... 7-9
DIRECT OUTPUTS
application example...........................................5-298, 5-299
clearing counters............................................................. 7-2
Modbus registers ................................B-14, B-15, B-68, B-69
settings ....................................................................... 5-297
DIRECTIONAL OVERCURRENT
see PHASE, GROUND, and NEUTRAL DIRECTIONAL entries
DIRECTIONAL POLARIZATION...................................... 5-181
DIRECTIONAL POWER
see entry for SENSITIVE DIRECTIONAL POWER
DISCONNECT SWITCH
FlexLogic operands ..................................................... 5-153
logic............................................................................ 5-114
settings ....................................................................... 5-112
DISPLAY ........................................................1-16, 4-22, 5-24
DISPOSAL..................................................................... 10-11
DISTURBANCE DETECTOR
FlexLogic™ operands .................................................. 5-152
internal ....................................................................... 5-105
DNA-1 BIT PAIR ............................................................ 5-295
DNP COMMUNICATIONS
binary counters ............................................................. F-10
binary input points ...........................................................F-8
binary output points .........................................................F-9
control relay output blocks ............................................... F-9
device profile document ................................................... F-1
frozen counters ............................................................. F-10
implementation table ....................................................... F-4
Modbus registers...........................................................B-31
settings ......................................................................... 5-37
DOWNED CONDUCTOR ........................................... 2-24, 6-9
DOWNED CONDUCTOR See
HI-Z
E
EGD PROTOCOL
actual values ........................................................ 6-10, 6-11
Modbus registers .......................................................... B-49
settings .........................................................................5-58
ELECTROSTATIC DISCHARGE........................................2-30
ELEMENTS ........................................................................5-4
EMAIL ADDRESS FOR SUPPORT ......................................1-2
END OF LIFE ................................................................. 10-11
ENERGY ALOGRITHM FOR HI-Z ........................................8-1
ENERGY METERING
actual values .................................................................6-20
Modbus registers .......................................................... B-18
specifications.................................................................2-24
ENERGY METERING, CLEARING.............................. 5-26, 7-2
ENERVISTA UR SETUP
creating a site list ............................................................4-1
event recorder .................................................................4-2
firmware upgrades ...........................................................4-2
installation .......................................................................1-5
introduction .....................................................................4-1
oscillography ...................................................................4-2
overview ..........................................................................4-1
requirements ...................................................................1-5
EQUATIONS
definite time curve ............................................ 5-176, 5-218
FlexCurve .................................................................... 5-176
I²t curves ..................................................................... 5-176
IAC curves................................................................... 5-175
IEC curves................................................................... 5-174
IEEE curves................................................................. 5-172
EQUIPMENT MISMATCH ERROR .......................................7-7
ETHERNET
actual values ...................................................................6-8
configuration....................................................................1-8
error messages..............................................................7-10
Modbus registers .......................................................... B-15
quick connect ..................................................................1-9
settings .........................................................................5-30
EVENT CAUSE INDICATORS .................................. 4-15, 4-16
EVENT RECORDER
actual values .................................................................6-28
clearing .................................................................. 5-25, 7-2
Modbus .......................................................................... B-8
Modbus registers .......................................................... B-24
specifications.................................................................2-23
via EnerVista software .....................................................4-2
EVENTS
syslog............................................................................5-23
EVENTS SETTING .............................................................5-5
EXCEPTION RESPONSES ................................................ B-6
EXPERT ARC DETECTOR ALGORITHM .............................8-2
F
F485 ................................................................................1-16
FACEPLATE ...............................................................3-1, 3-2
FACEPLATE PANELS ......................................................4-13
FACTORY DEFAULT RESET ..............................................5-8
FAR-END FAULT INDICATION .........................................5-31
FAST FORM-C RELAY .....................................................2-27
FAST TRANSIENT TESTING ............................................2-30