GE PACSystems RX3i User Manual

Contents
vi PACSystems* RX3i & RSTi-EP PROFINET IO-Controller User Manual GFK-2571N
Table of Figures
Figure 1: IC695PNC001-Bxxx Front View ___________________________________________________________ 4
Figure 2: IC695PNC001-Ax Controls & Indicators ____________________________________________________ 10
Figure 3: IC695PNC001-Bxxx Controls & Indicators __________________________________________________ 10
Figure 4: PNC001 Ethernet Ports Location and Type _________________________________________________ 12
Figure 5: CPE100/CPE115 Ethernet Ports Location and Type __________________________________________ 12
Figure 6: RX3i System with one PROFINET Controller and one PROFINET LAN _____________________________ 16
Figure 7: RX3i System with one PROFINET Controller and multiple PROFINET LANs ________________________ 17
Figure 8: RX3i System interfacing with Third-Party Devices and with PME Programmer ____________________ 18
Figure 9: RX3i System with two PNC001 Modules and one Daisy-Chain PROFINET LAN _____________________ 19
Figure 10: RX3i System with two PNC001 modules and two Daisy-Chain PROFINET LANs ___________________ 20
Figure 11: RX3i System with four PNC001 modules and four Daisy-Chain PROFINET LANs ___________________ 21
Figure 12: RX3i System with two PROFINET LANs & one Ethernet LAN __________________________________ 22
Figure 13: PROFINET System Redundancy S2 _______________________________________________________ 23
Figure 14: RX3i Hot Standby CPU Redundancy Network with MRP Ring Topology _________________________ 24
Figure 15: RSTi-EP System with embedded PROFINET Controller and one PROFINET LAN ____________________ 25
Figure 16: RX3i System with one PROFINET Controller and multiple PROFINET LANs _______________________ 26
Figure 17: RX3i System with one PROFINET Controller and PROFINET IO Network MRP _____________________ 27
Figure 18: RX3i Backplane showing Removable Plastic Knockout _______________________________________ 34
Figure 19: Install Module into RX3i Backplane ______________________________________________________ 35
Figure 20: Remove Module from RX3i Backplane ___________________________________________________ 35
Figure 21: Ethernet Ports on PNC001 Module ______________________________________________________ 37
Figure 22: Interconnect using Copper Cables / RJ45 Connectors ________________________________________ 38
Figure 23: Interconnect using Multi-Mode Fiber ____________________________________________________ 38
Figure 24: Interconnect using Single-Mode Fiber ____________________________________________________ 38
Figure 25: CAT5e/CAT6 (shielded or unshielded) with RJ 45 Connector __________________________________ 39
Figure 26: Multi-Mode Fiber with LC connector _____________________________________________________ 39
Figure 27: Single-Mode Fiber with LC connector ____________________________________________________ 39
Figure 28: Method for Attaching SFP Device Connector to PNC001 Port _________________________________ 40
Figure 29: Fiber SFP showing LC Connector ________________________________________________________ 42
Figure 30: Copper SFP showing RJ45 Connector ____________________________________________________ 42
Figure 31: PNC001-Bxxx Front View showing LEDs __________________________________________________ 43
Figure 32: RX3i Configuration showing PNC001 slot location __________________________________________ 53
Figure 33: Embedded PROFINET Controller Configured on LAN2 _______________________________________ 53
Figure 34: CPE100/CPE115 Embedded PROFINET Controller Configured on LAN2 __________________________ 54
Figure 35: Setting PROFINET System Redundancy Parameters in PME Inspector __________________________ 55
Figure 36: Explore PROFINET Network from PNC001 ________________________________________________ 56
Figure 37: Explore PROFINET Network from Embedded PROFINET Controller _____________________________ 56
Figure 38: LAN View showing PROFINET Controller on LAN2 __________________________________________ 57
Figure 39: LAN View showing PROFINET Controller on LAN1 __________________________________________ 57
Figure 40: PROFINET Controller Settings Tab (PNC001) _______________________________________________ 58
Figure 41: PROFINET Controller Settings Tab (Embedded PNC) ________________________________________ 58
Figure 42: Setting the Status Reference Address ____________________________________________________ 59
Figure 43: Select SFP Device from Catalog _________________________________________________________ 59
Figure 44: Setting Media Redundancy Parameters __________________________________________________ 61
Figure 45: Setting Media Redundancy Client Parameters _____________________________________________ 61
Figure 46: Setting Media Redundancy Manager Parameters __________________________________________ 61
Figure 47: Configuring the PROFINET LAN _________________________________________________________ 62
Figure 48: LAN Associated with PROFINET Controller ________________________________________________ 62
Figure 49: Adding a New LAN to the Configuration __________________________________________________ 62

GE PACSystems RX3i Specifications

General

Brand	GE
Model	PACSystems RX3i
Category	Controller
Language	English