What to do if my Gerber EDGE 2 Printer shows 'CHECK FOIL'?
If your Gerber Printer displays the message 'CHECK FOIL', ensure that the foil is correctly loaded. After confirming, press the ONLINE button to resume.
What to do if my Gerber EDGE 2 Printer shows 'CHECK VINYL'?
If the Gerber printer displays 'CHECK VINYL', verify that the vinyl is correctly loaded into the printer. Once you've confirmed the correct loading, press the ONLINE button to continue.
Why does my Gerber EDGE 2 display 'PAUSED'?
The 'PAUSED' message appears when the ONLINE button is pressed during printing. To resume printing, press ONLINE again. To return to OFFLINE status, press RESET.
What to do if my Gerber EDGE 2 Printer prints a line through the length of a job?
If your Gerber printer is producing a line through the length of the print job, start by cleaning the printhead and foils. If the issue persists, adjust the print settings to 'Dark' or 'Darker' via the Print Order icon in the Plot program.
What to do if my Gerber EDGE 2 Printer has imperfections in printing?
If you notice imperfections like voids, hair lines, or small unprinted areas in your print, wipe the vinyl with a clean, lint-free cloth and clean the exposed foil. If imperfections are present throughout the entire job, the printhead may be dirty.
What to do if my Gerber EDGE 2 shows a thermistor error?
If your Gerber printer displays a 'THERMISTOR ERROR', allow the printhead to cool down. Once it has cooled sufficiently, the 'Paused' message will appear.
What to do if my Gerber Printer has lines that are not on the X or Y axis (wrinkling)?
If you are experiencing lines that are not on the X or Y axis (wrinkling) in your print, ensure the dancer bar is free. Check that the C clips at each end of the dancer bar are not jammed in the slot of the dancer bar frame.
What to do if my Gerber Printer vinyl has stretched sprocket holes?
To prevent stretched sprocket holes in the vinyl, use materials approved by Gerber for the EDGE 2. Unroll the vinyl before printing and ensure you are using the tension arm roller.
What to do if my Gerber EDGE 2 Printer printed images are lifting from the material?
If printed images are lifting from the material, wait at least 15 minutes before applying transfer tape to the printed vinyl, film, or sheeting. Use only Gerber Standard Tack Application Tape.
What to do if my Gerber EDGE 2 has opacity problems?
If you are experiencing opacity issues, such as a light color (like yellow) not covering a dark vinyl (like purple), print a white or gray undercoat on the vinyl before printing the other colors in the job.
Details key features and capabilities of the GERBER EDGE 2 printer.
Outlines the organization of the manual and the topics covered in each chapter.
Provides contact information for support and troubleshooting assistance from Gerber.
Defines symbols and text styles used throughout the manual for clarity.
Highlights critical safety warnings and guidelines to prevent injury and equipment damage.
Instructions for safely unpacking and repacking the EDGE 2 printer for transport.
Lists the items included in the EDGE 2 printer's shipping boxes.
Specifies the necessary computer system configurations for the EDGE 2 to function correctly.
Step-by-step guide on establishing a physical connection between the EDGE 2 and the computer.
Instructions for integrating the EDGE 2 printer within the GRAPHIX ADVANTAGE software.
Explains the recommended materials and their importance for optimal print quality.
Guidance on proper storage and cleaning of vinyl materials to maintain print quality.
Instructions on how to properly set up and use the tensioner assembly for material feeding.
Detailed steps for correctly loading vinyl material into the EDGE 2 printer.
Comprehensive guide on how to install and secure a foil cartridge into the EDGE 2.
Explains the overall workflow from job creation to final print output, including cutting.
Factors and settings crucial for creating successful print jobs on the EDGE 2.
Detailed explanation of the keypad, display, and function of each key on the EDGE 2 control panel.
Step-by-step instructions on how to send a job and initiate the printing process on the EDGE 2.
Procedures for pausing, resuming, or canceling a print job during operation.
Steps to take when the foil runs out mid-job, including replacement and continuation.
Guidance on aligning and cutting printed jobs using a plotter with registration marks.
How to access and navigate the EDGE 2's setup menu for configuration.
Instructions for running built-in test patterns to diagnose printing issues.
How to adjust specific settings like test patterns, overlap, and checksum for optimal performance.
Steps to reset the EDGE 2 to its original factory default configurations.
Method for matching print jobs created on older EDGE models using spool files.
Lists common error messages and provides required actions to resolve them.
Solutions for common printing issues like registration errors, lines, and imperfections.
Guidance on troubleshooting issues that may occur during the EDGE 2's startup sequence.
Procedures for cleaning critical components to maintain print quality.
Instructions for cleaning moving parts and squeegees to ensure smooth operation.
Steps for cleaning the platen area to remove debris and maintain print surface integrity.
Guidance on locating and replacing the fuses in the EDGE 2 printer.
General| Print Technology | Thermal Transfer |
|---|---|
| Resolution | 300 dpi |
| Power Requirements | 100-240V AC, 50/60Hz |
| Connectivity | Serial |
| Media Types | Vinyl, Polyester |
| Min Sheet Size | N/A (Continuous roll media) |
| Max Material Thickness | 0.010 inches |
| Software Compatibility | Gerber Software |
To Next Page
