What does 'Left Lamp Short' mean on my Handicare PUMA 40 Wheelchair and what should I do?
A 'Left Lamp Short' means the control system has detected a short in either of the Lamp Circuits. Check the lamps, cables, and connections to the control system. If the error persists, the ISM may be defective.
What does 'Brake Lamp Short' mean on my Handicare PUMA 40 Wheelchair and how do I fix it?
A 'Brake Lamp Short' means the control system has detected a short in the Brake Lamp Circuit. Check the brake lamps, cables, and connections to the control system. If the error persists, the ISM may be defective.
What does 'PM Memory Error' mean on my Handicare PUMA 40?
A 'PM Memory Error' is a specific Power Module based trip. Check all cables and connections. Using the R-net PC Programmer, re-program the control system with either the most current specific program file for the wheelchair or the manufacturer's original programming file. If the error persists, the PM may be defective.
What does 'Bad Settings' mean on my Handicare Wheelchair and how can I correct them?
A 'Bad Settings' error indicates that the control system has detected incorrect or invalid program settings. Check all parameter settings and re-program the control system using the R-net PC Programmer. Make a note of the current parameter settings and then reset the control system to default settings. Re-program the required settings in small groups, cycling the power after each group to see if the error occurs. If the error persists, the PM may be defective.
What does 'Latched Timeout' mean on my Handicare Wheelchair and how can I fix it?
A 'Latched Timeout' error means the control system has detected that the programmed Latched Timeout time has been exceeded. Cycle the power and initiate Latched Mode. If the error persists, the Input Device may be defective.
What does 'Inhibit Active' mean on my Handicare Wheelchair and how do I resolve it?
An 'Inhibit Active' error means that one of the Inhibit inputs is active and in a latched state. Cycle the power, which will drop out of Latched Mode and might clear the error. Check all wiring and switches connected to the indicated Inhibits. If the error persists, the ISM may be defective.
What does it mean when the service indicator flashes once on Handicare PUMA 40?
This is likely a 'STALL' timeout caused by user error. Place the joystick in neutral and try again.
What does 'System Error' mean on my Handicare PUMA 40 Wheelchair and how can I fix it?
A 'System Error' indicates a fault that cannot be attributed to a specific module. Check all cables and connections. Cycle the power. If the error persists and the system contains 3rd party Modules: Disconnect all the none PGDT modules and cycle the power. If this has cleared the trip: Connect each 3rd party module in turn, cycling the power each time. If the trip reappears after one of the power cycles then the last module to have been added to the system must be defective. If the error persists, the PGDT control system may be defective.
What does it mean if ON/OFF light flashes 5 times on Handicare Mobility Aid?
General| Brand | Handicare |
|---|---|
| Model | PUMA 40 |
| Category | Wheelchair |
| Language | English |
Explains the purpose and scope of the service manual for mechanics.
Details the information found on the product's identification plate.
Explains warning and reference symbols used in the manual for clear communication.
Lists Puma 20 options that reduce the maximum user weight on a Puma 40 carrier.
Specifies requirements for service technicians performing repairs.
Outlines general safety information, temperature warnings, and interference precautions.
Illustrates and explains the meaning of various decals found on the wheelchair.
Lists mechanical tools required for settings and maintenance tasks.
Lists tools required for electronic settings and programming.
Explains how to use the parts lists for ordering replacement components.
Provides an overview of carrier and seat components with their corresponding page numbers.
Lists wiring harnesses and electronic modules for the Shark system.
Lists wiring harnesses and electronic modules for the R-net system.
Lists wiring harnesses and electronic modules for the DX2 system.
Lists wiring harnesses and electronic modules for the VR-2 system.
Details the regular maintenance schedule for the wheelchair, specifying tasks and responsibilities.
Introduces instructions for assembly, replacement, and adjustment of wheelchair components.
Guides on replacing Puma 20 motors, including compatibility and programming.
Details the procedure for converting drive direction from FWD to RWD and vice versa.
Provides steps for replacing carbon brushes in the motor assembly.
Explains the process for replacing the indoor/outdoor drive wheels.
Details the procedure for replacing the castor wheels.
Outlines steps for replacing the castor fork assembly.
Provides instructions for installing the direct access accessory.
Guides on installing the attendant steering system.
Details the procedure for replacing the wheelchair batteries, including safety precautions.
Explains how to replace the power module unit.
Details the process for adjusting the wheelchair's seating height.
Explains how to adjust the wheelchair's center of gravity for stability.
Explains how to adjust the electrical seat tilt angles.
Provides tables detailing seat tilt limitations based on various configurations.
Offers troubleshooting steps for castor wheel shimmy issues.
Lists common faults and remedies for the Shark system.
Lists common faults and remedies for the R-net system.
Lists common faults and remedies for the DX2 system.
Lists flash codes and their meanings for the DX2 Actuator Module.
Lists common faults and remedies for the VR-2 system.
Lists relevant CE directives and standards the product complies with.
Provides general technical specifications like battery details and dimensions.
Lists technical specifications for various Puma models (40/20, Sedeo Pro+/Pro/Lite/EasyFit).
Shows system diagrams for various control modules like Shark, DX2, R-net, VR-2.
Shows system diagrams for Shark control modules.
Shows system diagrams for DX2 control modules.
Shows system diagrams for R-net control modules.
Shows system diagrams for VR-2 control modules.
Provides definitions for terms used in the warranty section.
Outlines the warranty periods for different parts and components of the power wheelchairs.
To Next Page
