What does it mean when the service indicator flashes twice and the ON/OFF light flashes three times on a Handicare Wheelchair?
This indicates a battery fault or a defective M1 motor. Check the batteries and cabling, charge or replace the batteries, and check the motor connections and cabling. If the issue persists, the M1 motor may need to be replaced.
Why is the ON/OFF light flashing four times on my Handicare Scooter?
If the ON/OFF light flashes four times on your Handicare Scooter, it could be due to a faulty connection or a defective m2 motor. Check the motor connections and cabling. If the connections are fine, the m2 motor may need to be replaced.
What does it mean when the ON/OFF light flashes four times on my Handicare PUMA 40 Wheelchair?
If the ON/OFF light flashes four times, it means that either the connection of the m2 motor is faulty or the m2 motor is defective. Check the motor connections and cabling. If the problem persists, replace the m2 motor.
Why does Handicare Mobility Aid show Low Battery?
If your Handicare Mobility Aid displays a 'Low Battery' message, it means the control system has detected that the battery voltage has fallen below 16V. Check the condition of the batteries and their connections to the control system. If the issue persists after checking the batteries and connections, the Power Module may be defective.
What does Right Indicator Lamp Failed mean on my Handicare Scooter?
A 'Right Indicator Lamp Failed' on your Handicare Scooter means that the control system has detected a failure in either of the Indicator Circuits. Check the indicator bulbs, cables, and connections to the control system. If the error persists after the above checks have been made, then the ISM may be defective.
What does it mean if the ON/OFF light flashes twice on my Handicare Scooter?
If the ON/OFF light flashes twice on your Handicare Scooter, it indicates a DX accessory fault. The module displays a fault as a result of a programming fault or short circuit and/or overload of the accessories.
What does System Error mean on my Handicare Scooter?
The 'System Error' message on your Handicare Scooter indicates a trip that cannot be attributed to a specific module. Check all cables and connections and cycle the power. If the system contains 3rd party Modules, disconnect all the none PGDT modules and cycle the power.
What does Brake Lamp Short mean on Handicare Mobility Aid?
If your Handicare Mobility Aid displays 'Brake Lamp Short', it means the control system has detected a short in the Brake Lamp Circuit. Check the brake lamps, cables, and connections to the control system. If the trip persists, the ISM may be defective.
What causes an M1 Brake Error on my Handicare PUMA 40 Wheelchair?
An M1 Brake Error indicates a problem in the solenoid brakes or their connections. Check the solenoid brakes, cables, and connections to the control system. If the error persists, the Power Module may be defective.
What causes an M2 Brake Error on my Handicare PUMA 40 Wheelchair?
An M2 Brake Error indicates a problem in the solenoid brakes or their connections. Check the solenoid brakes, cables, and connections to the control system. If the error persists, the Power Module may be defective.
Explains the purpose and scope of the service manual for mechanics.
Details the information found on the product's identification plate.
Explains warning and reference symbols used in the manual for clear communication.
Lists Puma 20 options that reduce the maximum user weight on a Puma 40 carrier.
Specifies requirements for service technicians performing repairs.
Outlines general safety information, temperature warnings, and interference precautions.
Illustrates and explains the meaning of various decals found on the wheelchair.
Lists mechanical tools required for settings and maintenance tasks.
Lists tools required for electronic settings and programming.
Explains how to use the parts lists for ordering replacement components.
Provides an overview of carrier and seat components with their corresponding page numbers.
Lists wiring harnesses and electronic modules for the Shark system.
Lists wiring harnesses and electronic modules for the R-net system.
Lists wiring harnesses and electronic modules for the DX2 system.
Lists wiring harnesses and electronic modules for the VR-2 system.
Details the regular maintenance schedule for the wheelchair, specifying tasks and responsibilities.
Introduces instructions for assembly, replacement, and adjustment of wheelchair components.
Guides on replacing Puma 20 motors, including compatibility and programming.
Details the procedure for converting drive direction from FWD to RWD and vice versa.
Provides steps for replacing carbon brushes in the motor assembly.
Explains the process for replacing the indoor/outdoor drive wheels.
Details the procedure for replacing the castor wheels.
Outlines steps for replacing the castor fork assembly.
Provides instructions for installing the direct access accessory.
Guides on installing the attendant steering system.
Details the procedure for replacing the wheelchair batteries, including safety precautions.
Explains how to replace the power module unit.
Details the process for adjusting the wheelchair's seating height.
Explains how to adjust the wheelchair's center of gravity for stability.
Explains how to adjust the electrical seat tilt angles.
Provides tables detailing seat tilt limitations based on various configurations.
Offers troubleshooting steps for castor wheel shimmy issues.
Lists common faults and remedies for the Shark system.
Lists common faults and remedies for the R-net system.
Lists common faults and remedies for the DX2 system.
Lists flash codes and their meanings for the DX2 Actuator Module.
Lists common faults and remedies for the VR-2 system.
Lists relevant CE directives and standards the product complies with.
Provides general technical specifications like battery details and dimensions.
Lists technical specifications for various Puma models (40/20, Sedeo Pro+/Pro/Lite/EasyFit).
Shows system diagrams for various control modules like Shark, DX2, R-net, VR-2.
Shows system diagrams for Shark control modules.
Shows system diagrams for DX2 control modules.
Shows system diagrams for R-net control modules.
Shows system diagrams for VR-2 control modules.
Provides definitions for terms used in the warranty section.
Outlines the warranty periods for different parts and components of the power wheelchairs.
General| Brand | Handicare |
|---|---|
| Model | PUMA 40 |
| Category | Wheelchair |
| Language | English |
To Next Page
