What does PM Memory Error mean on Handicare Mobility Aid?
If your Handicare Mobility Aid displays 'PM Memory Error', it is a specific Power Module-based trip. Check all cables and connections. Using the R-net PC Programmer, re-program the control system with either the most current specific program file for the wheelchair or the manufacturer's original programming file. If the trip persists, the PM may be defective.
What does it mean when the ON/OFF light flashes 11 times on my Handicare PUMA 40 Wheelchair?
If the ON/OFF light flashes 11 times on your Handicare Wheelchair, it indicates a 'STALL' overload fault, meaning a motor is continually demanding too much power. Check the drive units. This fault is often caused by obstacles that are too high, or driving against walls and door frames, etc. It may also be caused by a difficult turn from a standing position.
What does it mean when the service indicator flashes twice and the ON/OFF light flashes three times on a Handicare Wheelchair?
This indicates a battery fault or a defective M1 motor. Check the batteries and cabling, charge or replace the batteries, and check the motor connections and cabling. If the issue persists, the M1 motor may need to be replaced.
What does 'Right Lamp Short' mean on my Handicare PUMA 40 Wheelchair and how do I fix it?
A 'Right Lamp Short' means the control system has detected a short in either of the Lamp Circuits. Check the lamps, cables, and connections to the control system. If the error persists, the ISM may be defective.
What does 'DIME Error' mean on my Handicare PUMA 40 Wheelchair and how can I fix it?
A 'DIME Error' indicates an identification conflict between two modules in the system. If a new module has been introduced: Disconnect the new module and cycle the power. If no error is present, connect the new module to the system and cycle the power. If the error reappears, the new module is the cause. If there have been no additions: Disconnect one module at a time and cycle the power.
What to do if my Handicare Scooter ON/OFF light doesn't turn on and the wheelchair won't move?
If the ON/OFF light doesn't illuminate and the Handicare Scooter remains stationary, consider these potential causes and solutions: * Ensure the controller plug is correctly inserted into the power module. It may be a stall timeout, place the joystick in neutral and try again. * Inspect the fuses and replace any that are defective. * Verify that the batteries are properly connected. * Check for loose battery connections and secure them.
What does System Error mean on my Handicare Scooter?
The 'System Error' message on your Handicare Scooter indicates a trip that cannot be attributed to a specific module. Check all cables and connections and cycle the power. If the system contains 3rd party Modules, disconnect all the none PGDT modules and cycle the power.
What does PM Memory Error mean on my Handicare Scooter?
A PM Memory Error on your Handicare Scooter is a specific Power Module based trip. Check all cables and connections.
What does Left Indicator Lamp Short mean on Handicare Mobility Aid?
If your Handicare Mobility Aid displays 'Left Indicator Lamp Short', it means the control system has detected a short in either of the Indicator Circuits. Check the indicators, cables, and connections to the control system. If the trip persists, the ISM may be defective.
How to fix service indicator flashes once on Handicare Mobility Aid?
If the service indicator flashes once on your Handicare Mobility Aid, it's likely a 'STALL' timeout due to user error. Place the joystick in neutral and try again.
Explains the purpose and scope of the service manual for mechanics.
Details the information found on the product's identification plate.
Explains warning and reference symbols used in the manual for clear communication.
Lists Puma 20 options that reduce the maximum user weight on a Puma 40 carrier.
Specifies requirements for service technicians performing repairs.
Outlines general safety information, temperature warnings, and interference precautions.
Illustrates and explains the meaning of various decals found on the wheelchair.
Lists mechanical tools required for settings and maintenance tasks.
Lists tools required for electronic settings and programming.
Explains how to use the parts lists for ordering replacement components.
Provides an overview of carrier and seat components with their corresponding page numbers.
Lists wiring harnesses and electronic modules for the Shark system.
Lists wiring harnesses and electronic modules for the R-net system.
Lists wiring harnesses and electronic modules for the DX2 system.
Lists wiring harnesses and electronic modules for the VR-2 system.
Details the regular maintenance schedule for the wheelchair, specifying tasks and responsibilities.
Introduces instructions for assembly, replacement, and adjustment of wheelchair components.
Guides on replacing Puma 20 motors, including compatibility and programming.
Details the procedure for converting drive direction from FWD to RWD and vice versa.
Provides steps for replacing carbon brushes in the motor assembly.
Explains the process for replacing the indoor/outdoor drive wheels.
Details the procedure for replacing the castor wheels.
Outlines steps for replacing the castor fork assembly.
Provides instructions for installing the direct access accessory.
Guides on installing the attendant steering system.
Details the procedure for replacing the wheelchair batteries, including safety precautions.
Explains how to replace the power module unit.
Details the process for adjusting the wheelchair's seating height.
Explains how to adjust the wheelchair's center of gravity for stability.
Explains how to adjust the electrical seat tilt angles.
Provides tables detailing seat tilt limitations based on various configurations.
Offers troubleshooting steps for castor wheel shimmy issues.
Lists common faults and remedies for the Shark system.
Lists common faults and remedies for the R-net system.
Lists common faults and remedies for the DX2 system.
Lists flash codes and their meanings for the DX2 Actuator Module.
Lists common faults and remedies for the VR-2 system.
Lists relevant CE directives and standards the product complies with.
Provides general technical specifications like battery details and dimensions.
Lists technical specifications for various Puma models (40/20, Sedeo Pro+/Pro/Lite/EasyFit).
Shows system diagrams for various control modules like Shark, DX2, R-net, VR-2.
Shows system diagrams for Shark control modules.
Shows system diagrams for DX2 control modules.
Shows system diagrams for R-net control modules.
Shows system diagrams for VR-2 control modules.
Provides definitions for terms used in the warranty section.
Outlines the warranty periods for different parts and components of the power wheelchairs.
General| Brand | Handicare |
|---|---|
| Model | PUMA 40 |
| Category | Wheelchair |
| Language | English |
To Next Page
