Simple troubleshooting
79
Error Detail
LED
Power Light Temp Fan
SYS_ERR_G781_2 Thermal sensor IC initial failed (PW T3) 4 6
SYS_ERR_ADS1015 Thermal sensor IC initial failed (T1/T4/T5) 4 7
SYS_ERR_DRIVERBOARD_
Comm_Fail
Laser driver failed on communication 8 1 - -
SYS_ERR_DRIVERBOARD_
Speed_CW
Laser driver failed on CW-1 8 2 - -
SYS_ERR_DRIVERBOARD_
Speed_PW
Laser driver failed on CW-2 8 3 - -
SYS_ERR_DRIVERBOARD_54V Laser driver failed on power input 8 4 - -
SYS_ERR_DRIVERBOARD_
Temp
Laser driver failed on over temperature 8 5 - -
SYS_ERR_DRIVERBOARD_SCI Laser driver failed on control On/Off signal 8 6 - -
SYS_ERR_FAN1LOCK Fan-1 error 6 1 - Fix
SYS_ERR_FAN2LOCK Fan-2 error 6 2 - Fix
SYS_ERR_FAN3LOCK Fan-3 error 6 3 - Fix
SYS_ERR_FAN4LOCK Fan-4 error 6 4 - Fix
SYS_ERR_FAN5LOCK Fan-5 error 6 5 - Fix
SYS_ERR_FAN6LOCK Fan-6 error 6 6 - Fix
SYS_ERR_FAN7LOCK Fan-7 error 6 7 - Fix
SYS_ERR_FAN8LOCK Fan-8 error 6 8 - Fix
SYS_ERR_FAN9LOCK Fan-9 error 6 9 - Fix
SYS_ERR_CASEOPEN Error on projector case open 7 - - -
SYS_ERR_LENSOPEN Error on projector lens open 7 1 - -
SYS_ERR_DAD DAD1000 error 8 - - -
SYS_ERR_CWSPIN Laser driver failed on CW-1 (Scaler) 9 - - -
SYS_ERR_PWSPIN Laser driver failed on CW-2 (Scaler) 9 1 - -
SYS_ERR_OVERTEMP_T1 Over temperature on T1 - 1 Fix -
SYS_ERR_I2C_T1 I2C Fail on T1 - 1 Fix -
SYS_ERR_OPEN_T1 Sensor open on T1 - 1 Fix -
SYS_ERR_OVERTEMP_T2 Over temperature on T2 - 2 Fix -
SYS_ERR_I2C_T2 I2C Fail on T2 - 2 Fix -
SYS_ERR_OPEN_T2 Sensor open on T2 - 2 Fix -
SYS_ERR_OVERTEMP_T3 Over temperature on T3 - 3 Fix -
SYS_ERR_I2C_T3 I2C Fail on T3 - 3 Fix -
SYS_ERR_OPEN_T3 Sensor open on T3 - 3 Fix -
SYS_ERR_OVERTEMP_T4 Over temperature on T4 - 4 Fix -
SYS_ERR_I2C_T4 I2C Fail on T4 - 4 Fix -
SYS_ERR_OPEN_T4 Sensor open on T4 - 4 Fix -
SYS_ERR_OVERTEMP_T5 Over temperature on T5 - 5 Fix -
SYS_ERR_I2C_T5 I2C Fail on T5 - 5 Fix -
SYS_ERR_OPEN_T5 Sensor open on T5 - 5 Fix -
SYS_WARNING_LASER_LIFE Laser life time is over warning - Fix - -
To Next Page
Loading...
