Why are level and pressure values scaled up incorrectly from Honeywell Gateway CIU 888?
If the level value in mm and pressure value in Kgf/cm2 are scaled up and shown incorrectly from CIU 888, it indicates that the Modbus scaling factor for these parameters was increased during database configuration. To fix this, reset the scaling factors for these entities on the host ports using Ensite Pro.
Why are flexconn commands not working after NOVRam reset on Honeywell Gateway?
After a NOVRam reset, if the flexconn commands are not working for a particular flexline radar gauge, it means that the FlexConn address is wrongly configured for radar gauges in CIU 888. To resolve this: 1. Change the flexconn address using SmartView. 2. If the configuration has 8xx gauge type, change the gauge type to 990 and assign a non-used flexconn address. Then, revert the gauge type back to 8xx gauge type.
Why is the Honeywell Gateway CIU 888 ring of light orange?
If the CIU System Status or Ring of light is orange, this indicates a warning that the compact flash data free space is less than the required limit (below 300MBs). To resolve this, clear the log files by accessing the CIU 888 web interface (https:// 192.168.1.1), entering your credentials, clicking 'clear logs', and then restarting the CIU 888.
Why does NOVRam reset command fail for Honeywell Gateway gauge?
If the NOVRam reset command fails for a gauge, it is possible that there are some unresponsive gauges periodically scanned by CIU 888. Disable tank scan for these unresponsive gauges.
Why does a Honeywell Gateway CIU go to factory reset after configuration update in redundant setup?
In a redundant CIU configuration, if one of the CIUs goes to a factory reset status after a configuration update, it means the CIUs site topology has dual masters (two systems issuing switchover commands, such as Entis Pro and Experion). During the configuration update, multiple switchovers are initiated, causing the CIU to go into factory reset status. If the CIU enters this state, reset both CIUs and perform the setup redundancy procedure to recover. Ensure that the site topology has only one Master (one host system controls CIU redundancy and issues switchover commands) to prevent this issue.
How to delete a tank in Honeywell Gateway Service tool?
To delete a tank: 1. Change the protocol type back to Modbus RTU. 2. Change the Modbus mapping to user specified. 3. Remove the tank which needs to be deleted from the Service tool and add it to the available list in the user-defined Modbus map. 4. Delete the tank from the Service tool.
What to do if secondary Honeywell Gateway CIU 888 is not able to assume primary or secondary role after restart?
If the secondary CIU 888 in a redundant system setup is unable to assume either the primary or secondary role after a restart, it is possible that the Sync Link cable between the CIU 888s is disconnected. To resolve this, reconnect the Sync Link cable between the CIU 888s and then restart the secondary CIU 888.
Why is the Honeywell Gateway CIU 888 status striked out in Entis Pro Hot Standby?
If the CIU 888 status is striked out in the Hot Standby status of Entis Pro, it could be due to these reasons: * The serial cable between the Entis Pro system and CIU 888 is disconnected or malfunctioning. Reconnect the serial cable. If the cable is faulty, replace it. * There is a mismatch between Tank and CIU 888 CRCs within CIU 888 due to database corruption. This can be observed in the Logs window of the CIU 888 Web interface, and the ring of light may be red. In this case, perform a Reset to Factory Settings operation via the CIU 888 display and upload a new site configuration to CIU 888 using the Service tool/ Migration tool.
What to do if I get 'Cannot connect to remote server' message when uploading site configuration to Honeywell Gateway CIU 888?
If you encounter the message “Cannot connect to remote server” when uploading a site configuration to the CIU 888 using the Service tool or Migration tool, it indicates that the cable used for connecting your PC/laptop to the Service port/VPN port of CIU 888 is not connected properly. Ensure that the cable is securely connected to the Service/VPN port of CIU 888.
How to fix 'Active session exists' message when uploading site configuration to Honeywell Gateway CIU 888?
If you receive an “Active session exists” message when uploading a site configuration to CIU 888 using the Service tool or Migration tool, it means that you are already logged on to CIU 888. To resolve this, close any existing session with CIU 888 before uploading the site configuration again.
General| Brand | Honeywell |
|---|---|
| Model | CIU 888 |
| Category | Recording Equipment |
| Language | English |
Instructions for installing the CIU 888 Service Tool.
Detailed steps for installing the service tool on a new machine.
Overview of functionalities and access to the CIU 888 Web interface.
First step in configuration: creating a site using the Service Tool.
Procedure for creating a new site configuration in the Service Tool.
Steps for configuring serial, Ethernet, and TRL/2 field ports.
Procedures for configuring tank settings under serial and Ethernet ports.
Adding data inputs for GPU, Modbus, or TRL/2 devices.
Configuration of serial and Ethernet host ports.
Creating and managing user-defined Modbus maps.
Steps for configuring FTE A, FTE B, and LAN ports.
Creating, deleting, and editing TCP/IP Modbus maps.
Process for sending site configuration to the CIU 888.
Steps to generate INI files for Entis Pro.
Procedure to verify the current configuration of the CIU 888.
Performing the initial setup and login for the CIU 888.
Procedure for initial login and password change on CIU 888.
Steps to verify if the CIU 888 license is installed and valid.
Managing self-signed certificates for OPCUA communication.
Managing CA-signed certificates for OPCUA communication.
Performing initial setup for the primary CIU 888 in a redundant system.
Setting up site configuration for primary CIU 888.
Sending the configured site setup to the primary CIU 888.
Configuring the secondary CIU 888 as a counterpart.
Steps to implement changes in the site configuration.
Sending updated site configuration to CIU 888.
Procedure for updating configuration on redundant CIU without restart.
Procedures for starting, restarting, and shutting down the CIU 888.
Configuration steps for integrating redundant CIU 888 with Experion PKS.
Steps for required Experion PKS configuration using Quick Builder.
To Next Page