Honeywell Thor VM3 Manual

5 - 8
Manual
1. Select Bluetooth Scanning from the Control Panel (either large or small icon view option must be selected).
2. Tap Add Device.
3. Select Manual.
4. Tap Next.
5. Enter the MAC address of the Bluetooth scanner.
6. Tap Next.
Troubleshooting
• The Honeywell Xenon 1902 Bluetooth scanner does not work with Quick Connect. It must be connected using the
Search or Manual options.
• Make sure the scanner is in the correct mode. Bar codes to set the mode can be found in the manual provided with
the Bluetooth scanner.
» The scanner must be a master device to use the Quick Connect option.
» The scanner must be a slave device to use the Search or Manual option.
• The Motorola/Symbol LS3578 family of scanners may not support the Quick Connect feature (depending on firmware
installed). If Quick Connect does not work, use the other options to connect these scanners.
• If the Honeywell Granit 1911i and Granit 1981i scanners cannot be found with the Search option, scan the PDAs/
Mobility Systems Devices bar code from the scanner manual and search again.
• If the Honeywell Granit 1911i and Granit 1981i scanners cannot connect using the manual option, scan the PDAs/
Mobility Systems Devices bar code from the scanner manual then repeat the manual add process again.
• If the Honeywell Granit 1911i and Granit 1981i scanners are not removed after using the Remove option, the auto-
reconnect option is enabled on the Granit scanner (this is the default option). To remove the scanner:
» Scan the disable auto-reconnect bar code from the Granit scanner manual then tap Remove, or
» Scan BT_RMV to unlink and disconnect the scanner the tap Remove.
• If a Honeywell/LXE ring scanner is not connecting, scan the Restore Factory Defaults bar code in the scanner
manual and try connecting again.
Adding Other Scanners
Some scanners may not be supported/discoverable by Bluetooth Scanning. In this case, use the Microsoft Bluetooth
panels to add the scanner.
Note: The Microsoft Bluetooth panels should only be used when the scanner cannot be connected with one of the
methods listed above.

Honeywell Thor VM3 Specifications

General

Stepping	D0
Tjunction	-40 °C
FSB Parity	No
Processor code	SR1X8
Processor cache	1 MB
Processor cores	2
Processor model	E3826
System bus rate	- GT/s
Processor family	Intel Atom®
Processor codename	Bay Trail
Processor frequency	1.46 GHz
Processor cache type	L2
Processor manufacturer	Intel
Processor package size	25 x 27 mm
Conflict-Free processor	Yes
Processor front side bus	- MHz
Processor operating modes	32-bit, 64-bit
Graphics & IMC lithography	22 nm
PCI Express configurations	1x1, 1x4, 2x1
Thermal Design Power (TDP)	7 W
Internal memory	4 GB
Internal memory type	DDR3-SDRAM
Storage media	Flash
Compatible memory cards	-
Internal storage capacity	64 GB
Display diagonal	12.1 \
Display brightness	900 cd/m²
Display resolution	1024 x 768 pixels
Graphics card	HD Graphics
Rear camera resolution (numeric)	- MP
Wi-Fi standards	802.11a, 802.11b, 802.11g
Bluetooth version	2.0+EDR
Top Wi-Fi standard	Wi-Fi 4 (802.11n)
HDMI ports quantity	0
USB 2.0 ports quantity	1
I/O ports	1x CAN-bus, RF
Processor ARK ID	78477
Processor socket	BGA 1170
Operating temperature (T-T)	-30 - 50 °C
Operating relative humidity (H-H)	5 - 95 %
Platform	Windows
Bundled software	Data Collection Engine, Microsoft Internet Explorer, Microsoft on-screen keyboard, Configuration Cloning Utility, Screen Blanking, Zoom Zone, Launcher
Operating system installed	Windows 7
AC adapter input voltage	90 - 240 V
Battery capacity	- mAh
Battery life (max)	0.5 h
Certification	EN 55024:2010, MIL-STD-810F, SAE-J1455, CCX
Device type	Tablet PC
Form factor	Slate
Product color	Grey, Silver
Protection features	Shock resistant, Vibration proof, Water resistant
International Protection (IP) code	IP66
Harmonized System (HS) code	84713000

Weight and Dimensions

Depth	62 mm
Width	318 mm
Height	260 mm
Weight	3000 g