Honeywell Thor VM3 Manual

4 - 42
Connect Serial Device
Note: Pin 9 of the desired COM port must be configured to provide +5V or RI as needed for the connected device. See the
Options (page 5-17) control panel for details.
Note: Pin 9 of the desired COM port must be configured to provide +5V or RI as needed for the connected device. See the
Options (page 5-43) control panel for details.
Note: Pin 9 of the COM port is configured to provide +5V.
Note: By default, COM1 and COM2 ports are used by Enterprise Data Collection. To use a COM port for screen blanking,
access Enterprise Settings (page 5-27) and set Data Collection > Tethered Scanners > Tethered Scanner (COMx)
- Enable Scanner Port to off (where COMx is either COM1 or COM2).
Note: By default, COM1 and COM2 ports are used by Enterprise Data Collection. To use a COM port for screen blanking,
access Enterprise Settings (page 5-10) and set Data Collection > Tethered Scanners > Tethered Scanner (COMx)
- Enable Scanner Port to off (where COMx is either COM1 or COM2).
See COM1 and COM2 Connector (page 9-6) for connector pinouts.
1. Seat the cable end connector firmly over the serial COM port on the Smart Dock.
2. Turn the thumbscrews in a clockwise direction. Do not over tighten.
3. Secure the cables to the Thor VM3 with Strain Relief Cable Clamps (page 4-16).
4. Connect the other cable end to the desired serial device.
Connect a Tethered Scanner
1. The scanner cable is attached to either the COM1 or COM2 port on the Smart Dock.
2. Connect the serial cable for the scanner as directed above.
3. When the Thor VM3 is powered on, it provides power to the serial scanner.
4. Configure the Data Collection (DC) Wedge to manipulate scanned data as desired.
Connect Headset Cable
The CANbus/Audio connector supports a headset adapter cable or a CANbus cable. The Thor VM3 does not support con-
necting audio and CANbus simultaneously.
See CANbus / Audio Connector (page 9-11) for connector pinouts.
1. Seat the D15 cable end connector firmly over the CANbus/Audio Connector on the Smart Dock.
2. Tighten the thumbscrews in a clockwise direction. Do not over tighten.
Headphones
Microphone
To Audio cable
To Audio
connector
on dock
To headset

Honeywell Thor VM3 Specifications

General

Stepping	D0
Tjunction	-40 °C
FSB Parity	No
Processor code	SR1X8
Processor cache	1 MB
Processor cores	2
Processor model	E3826
System bus rate	- GT/s
Processor family	Intel Atom®
Processor codename	Bay Trail
Processor frequency	1.46 GHz
Processor cache type	L2
Processor manufacturer	Intel
Processor package size	25 x 27 mm
Conflict-Free processor	Yes
Processor front side bus	- MHz
Processor operating modes	32-bit, 64-bit
Graphics & IMC lithography	22 nm
PCI Express configurations	1x1, 1x4, 2x1
Thermal Design Power (TDP)	7 W
Internal memory	4 GB
Internal memory type	DDR3-SDRAM
Storage media	Flash
Compatible memory cards	-
Internal storage capacity	64 GB
Display diagonal	12.1 \
Display brightness	900 cd/m²
Display resolution	1024 x 768 pixels
Graphics card	HD Graphics
Rear camera resolution (numeric)	- MP
Wi-Fi standards	802.11a, 802.11b, 802.11g
Bluetooth version	2.0+EDR
Top Wi-Fi standard	Wi-Fi 4 (802.11n)
HDMI ports quantity	0
USB 2.0 ports quantity	1
I/O ports	1x CAN-bus, RF
Processor ARK ID	78477
Processor socket	BGA 1170
Operating temperature (T-T)	-30 - 50 °C
Operating relative humidity (H-H)	5 - 95 %
Platform	Windows
Bundled software	Data Collection Engine, Microsoft Internet Explorer, Microsoft on-screen keyboard, Configuration Cloning Utility, Screen Blanking, Zoom Zone, Launcher
Operating system installed	Windows 7
AC adapter input voltage	90 - 240 V
Battery capacity	- mAh
Battery life (max)	0.5 h
Certification	EN 55024:2010, MIL-STD-810F, SAE-J1455, CCX
Device type	Tablet PC
Form factor	Slate
Product color	Grey, Silver
Protection features	Shock resistant, Vibration proof, Water resistant
International Protection (IP) code	IP66
Harmonized System (HS) code	84713000

Weight and Dimensions

Depth	62 mm
Width	318 mm
Height	260 mm
Weight	3000 g