HORNER EXL6 0 - Set Beeper

To Next Page

To Previous Page

MAN1032-10-EN_EXL6_UserManual

March 12, 2020 39 | 191

5.12 Set Beeper

The Set Beeper Sub-Menu displays one System Setting, which may be edited.

Beeper enable

Yes

(default)

= Enables beeper

No = Disables beeper

(does NOT affect ladder access)

Main Page

Default Chapter2
- Preface2
- About Programming Examples3
- Limited Warranty and Limitation of Liability3
- Visual Map of Chapters4
- Table of Contents5
Chapter 1: Safety and Compliance10
- Safety Warnings and Guidelines10
- Grounding11
- Compliance11
Chapter 2: Introduction12
- Visual Overview of EXL612
- Connectivity to the EXL6 OCS14
- Features of EXL6 OCS15
- Required and Suggested Accessories16
- Useful Documents and References16
- Opening Cscape Help File16
Chapter 3: Mechanical Installation17
- Overview17
- Mounting Requirements17
- Mounting Orientation18
- Panel Cut-Out19
- EXL6 Dimensions20
- Factors Affecting Panel Layout Design and Clearances21
Chapter 4: Electrical Installation23
- Grounding Definition23
- Ground Specifications23
- How to Test for Good Ground24
- Primary Power Port25
Chapter 5: System Settings and Adjustments26
- System Menu - Overview26
- System Menu - Navigation and Editing27
- System Menu - Details29
- View Status30
- View Diags31
- View Battery Status32
- View I/O Slots33
- View Protocols34
- Set Fkeys Mode35
- Set Serial Ports36
- Set Time/Date37
- Set Beeper39
- Set Screen40
- Removable Media41
- Fail - Safe System42
- Autorun43
- Autoload44
- Clone Overview45
- Load Clone46
- License Details47
- Touch Calibration Screen48
Chapter 6: Registers49
- Register Definitions49
- Useful %S and %SR Registers50
- Register Map for EXL6 OCS I/O58
- Resource Limits59
Chapter 7: Cscape Configuration60
- Overview60
- Cscape Status Bar60
- Establishing Communications61
- Configuration69
- Digital / HSC Input Configuration71
- Digital / PWM Output Configuration72
- Analog Input Configuration73
- Analog Output Configuration74
Chapter 8: General I/O75
- Overview75
- Removing the EXL6 OCS I/O Cover75
- Model and I/O Overview77
- Solid-State Digital Outputs78
- Relay Outputs79
- Digital Inputs80
- Analog Inputs81
- Universal Analog Inputs Model 581
- Universal Analog Inputs Model 6 Universal Analog Inputs82
- Analog Outputs83
Chapter 10: High Speed I/O84
- Overview84
- Glossary85
- High Speed Counter (HSC) Functions86
- Frequency86
- Totalize86
- Pulse Width Measurement88
- Period Measurement89
- Quadrature90
- Register Match91
- HSC Functions92
- Status Bits93
- HSC Functions Register Map94
- High Speed Output Functions97
- High-Speed Output Functions Register Map101
- PWM Examples102
- STP Examples103
- HSC I/O Filtering104
Chapter 11: Serial Communications107
- Overview107
- Port Descriptions107
- Wiring and Dip Switches107
- RS485 Termination108
- RS485 Biasing108
- Cscape Programming Via Serial Port109
- Ladder-Controlled Serial Communication109
- Configuration Via Mini-B USB109
CHAPTER 12: CAN Communications110
- Overview110
- Port Description110
- CAN Port Wiring110
- Cscape Programming Via CAN111
- Ladder-Controlled CAN Communication111
- Using CAN for I/O Expansion (Network I/O)111
Chapter 13: Etherenet Communication112
- Ethernet Module Protocols and Features112
- Ethernet System Requirements112
- Ethernet Module Specifications112
- Ethernet Module Configuration113
- Ethernet Configuration - IP Parameters117
- Ethernet Module Protocol Configuration117
Chapter 14: Downloadable Communication Protocols118
- Overview118
- Protocol Config120
- Network Configuration121
- Device List and Device Configuration123
- Scan List124
- Data Mapping Configuration (Scan List Entry)125
Chapter 15: User Interface127
- Overview127
- Screen Specifications127
- Displaying and Entering Data128
- Alpha-Numeric Keypad129
- Screen Navigation131
- Ladder Based Screen Navigation132
- Beeper Acknowledgement133
- Touch (Slip) Sensitivity133
- Alarms134
- Removable Media136
- Screen Saver138
- Screen Brightness138
- Touch Screen Pressure139
CHAPTER 16: VIDEO OBJECT for EXL6141
- Video Object Overview141
- Opening Video Object in Cscape142
- Video Properties: Video Type144
- Video Properties: Control145
- Configuring Display Properties146
- Video Object Performance146
- Web Cameras146
Chapter 17: Removable Media147
- Overview147
- Removable Microsd Cards147
- File System for Microsd Cards148
- Using the Removable Media Manager148
- Using Removable Media to Log Data149
- Using Removable Media to Load and Save Applications149
- Using Removable Media to View and Capture Screens150
- Configuration of a Removable Media150
- Removable Media (RM) Function Blocks in Cscape151
- Removable Media (RM) Features-Program Features151
- Removable Media (RM) Features-Graphic/Screen Editor151
- Removable Media (RM) Features-Additional Configuration152
- Filenames Used with the Removable Media (RM) Function Blocks152
- System Registers Used with RM153
Chapter 18: Clone Unit154
- Overview154
- Clone154
- Load Clone158
Chapter 19: Fail - Safe System160
- Overview160
- Settings161
- Backup / Restore Data161
- Backup OCS Data162
- Restore OCS Data163
- Clear Backup Data164
- Autoload166
- Autorun168
Chapter 20: Modbus Communications169
- Modbus Overview169
- Modbus Slave Overview169
- Modbus Master Overview170
- Modbus Addressing Table for EXL6 Units171
Chapter 21: Back-Up Battery172
- Overview172
- Storing Register Contents172
- Battery Life172
- Lithium Battery Safety172
- Battery Charging Cycle173
- Battery Charging Status173
- Battery Charging State173
- Battery Status in System Registers173
Chapter 22: Maintenance174
- Firmware Updates174
- How to Check for Current Firmware Revision174
- Updating Firmware Details175
- Steps for Updating the Firmware176
- Replacing Backup Battery177
Chapter 23: Troubleshooting / Technical Support179
- Connecting to the EXL6 OCS179
- Local Controller and Local I/O181
- Cscan Network182
- Technical Support Contacts183
- Change Log184
- Main Index185
- Index of Figures and Tables189

HORNER EXL6 0 - Set Beeper

Table of Contents

Other manuals for HORNER EXL6 0

Related product manuals