HORNER HEXT251C216

To Next Page

To Previous Page

MAN0964-13-EN_XL4_UM

A u g u s t 6 , 2 0 2 1 P a g e 190 | 194

Change Log

Date

Rev #

Description of Revision with Mantis #

Location in Doc

8-5-2021

#4845 – Updated WebMI register

#4802 – WebMI – Max # of connections

Added latest Firmware Update steps

#6482 – Updated Install Procedure

#6319 – USB Interfaces

#6442 – Battery Charging Cycle

%SR Table

Ethernet Overview

Firmware Updates

Installation Procedure

USB Interfaces

Battery Status in SR

Main Page

default chapter2
- Preface2
- About Programming Examples3
- Limited Warranty and Limitation of Liability3
- Visual Map of Key Chapters4
- Table of Contents5
Chapter 1: Safety/ Compliance10
- Safety Warnings and Guidelines10
- Grounding11
- CE Compliance11
Chapter 2: Introduction12
- Visual Overview of XL4 OCS12
- Connectivity to the XL4 OCS14
- Features of XL4 OCS15
- Useful Documents and References15
Chapter 3: Mechanical Installation16
- Overview16
- Mounting Requirements16
- Mounting Orientation17
- Dimensions18
- Installation Procedure19
- Factors Affecting Panel Layout Design and Clearances20
Chapter 4: Electrical Installation22
- Grounding Definition22
- Ground Specifications22
- How to Test for Good Ground23
- Primary Power Port24
Chapter 5: System Settings and Adjustments25
- System Menu - Overview25
- System Menu - Navigation and Editing27
- System Menu - Details28
- View Status29
- View Diags30
- View Battery Status31
- View I/O Slots32
- View Protocols33
- Set Fkeys Mode34
- Set Serial Ports35
- Set Time/Date36
- Set Beeper38
- Set Screen39
- Removable Media40
- Enable Autorun42
- Enable Autoload43
- Clone Unit44
- Load Clone46
- Webmi License Details47
- Touch Screen Calibration48
Chapter 6: Registers49
- Register Definitions49
- Useful %S and %SR Registers50
- Resource Limits59
- Register Map for XL4 OCS I/O60
Chapter 7: Cscape Configuration62
- Overview62
- Cscape Status Bar62
- Establishing Communications63
- Configuration71
- Digital / HSC Input Configuration72
- Digital / PWM Output Configuration73
- Analog Input Configuration74
- Analog Output Configuration76
- Scaling Analog Inputs77
Chapter 8: General I/O78
- Overview78
- Removing the XL4 OCS I/O Cover78
- Model and I/O Overview79
- Solid-State Digital Outputs80
- Relay Outputs81
- Digital Inputs82
- Analog Inputs83
- Universal Analog Inputs84
- Analog Outputs85
Chapter 9: High Speed I/O (Hsc / Pwm)86
- Overview86
- Glossary87
- High Speed Counter (HSC) Functions88
- HSC Functions Register Map97
- High Speed Output Functions100
- High Speed Output Functions Register Map104
- PWM Examples106
- STP Examples107
- HSC I/O Filtering108
Chapter 10: Serial Communications112
- Overview112
- Port Descriptions112
- Serial Port112
- Dip Switches113
- Termination113
- Biasing114
- Cscape Programming Via Serial Port114
- Ladder-Controlled Serial Communication114
- Configuration Via Mini-B USB114
Chapter 11: Can Communications115
- Overview115
- Port Description115
- CAN1 Port Wiring116
- Cscape Programming Via CAN116
- Ladder-Controlled CAN Communication116
- Using CAN for I/O Expansion (Network I/O)116
Chapter 12: Ethernet Communication117
- Ethernet Overview117
- Ethernet Module Protocols and Features117
- Ethernet System Requirements117
- Ethernet Module Specifications118
- Ethernet Module Configuration119
- Ethernet Configuration - IP Parameters122
- Ethernet Module Protocol Configuration122
Chapter 13: Downloadable Communication Protocols123
- Overview123
- Protocol Config125
- Network Configuration126
- Device List and Devices Configuration128
- Scan List129
- Data Mapping Configuration (Scan List Entry)130
Chapter 14: User Interface132
- Overview132
- Screen Specifications132
- Displaying and Entering Data133
- Alpha-Numeric Keypad134
- Screen Navigation136
- Ladder Based Screen Navigation136
- Beeper Acknowledgement137
- Touch (Slip) Sensitivity137
- Alarms138
- Removable Media140
- Screen Saver142
- Screen Brightness142
- Touch Screen Pressure143
Chapter 15: Video Object145
- Video Object Overview145
- Opening Video Object in Cscape146
- Video Properties: Video Type148
- Video Properties: Control149
- Configuring Display Properties150
- Video Object Performance150
- Web Cameras150
Chapter 16: Removeable Media151
- Overview151
- Microsd Cards151
- Microsd File System152
- Using the Removable Media Manager152
- Using Removable Media to Log Data153
- Using Removable Media to Load and Save Applications153
- Using Removable Media to View and Capture Screens153
- Configuration of the Removable Media Object154
- Removable Media (RM) Function Blocks in Cscape154
- Removable Media (RM) Features-Program Features155
- Removable Media (RM) Features-Graphic/Screen Editor155
- Removable Media (RM) Features-Additional Configuration155
- Filenames Used with the Removable Media (RM) Function Blocks156
- System Registers Used with RM157
Chapter 17: Clone Unit158
- Overview158
- Make Clone158
- Load Clone162
Chapter 18: Fail - Safe System164
- Overview164
- Settings165
- Backup / Restore Data165
- Autoload170
- Autorun172
Chapter 19: Modbus Communications173
- Modbus Overview173
- Modbus Slave Overview173
- Modbus Master Overview174
- Modbus Addressing Table175
Chapter 20: Back-Up Battery176
- Overview176
- Storing Register Contents176
- Battery Life176
- Lithium Battery Safety176
- OCS Battery Charging Cycle177
- Battery Charging Status178
- Battery Status in System Registers179
Chapter 21: Maintenance180
- Firmware Updates180
- How to Check for Current Firmware Revision180
- Firmware Update Details181
- Firmware Update Steps182
- Replacing Backup Battery183
Chapter 22: Troubleshooting / Technical Support185
- Connecting to the XL4 OCS185
- Local Controller and Local I/O187
- Cscan Network187
- USB Interfaces189
- Basic Troubleshooting189
- Technical Support Contacts189

HORNER HEXT251C216 - Page 190

Table of Contents

Related product manuals