EasyManuals Logo

HP 37717C Calibration Manual

HP 37717C
399 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #37 background imageLoading...
Page #37 background image
1-16
General Information
Specifications
700 kb/s to 170 Mb/s (ECL)
Format: NRZ
Source impedance: Nominal TTL into
75 to ground or nominal ECL
into75 to -2V
Return loss: Typically >15 dB, 500
kHz to 100 MHz (TTL)
Binary Clock Output
Clock rates: 700 kb/s to 50 Mb/s
(TTL), 700 kb/s to 170 Mb/s (ECL)
Format: Nominal squarewave 60/40 to
40/60 duty cycle.
Source impedance: Nominal TTL into
75 to ground or nominal ECL into
75 to -2V
Return loss: Typically >10 dB, 500
kHz to 100 MHz (TTL)
External Clock Input
Clock rates: 700 kb/s to 50 Mb/s
(TTL), 700 kb/s to 170 Mb/s (ECL)
Logic threshold:1.5V (TTL), -1.3V
(ECL), ground (0V), signal mean level.
Termination: Nominal TTL into 75
to ground or nominal ECL into75 to
-2V
Format: Nominal squarewave 60/40 to
40/60 duty cycle.
Return loss: Typically >15 dB, 500
kHz to 200 MHz (TTL)
Receiver
Binary Data Input
Data rates: 700 kb/s to 50 Mb/s (TTL),
700 kb/s to 170 Mb/s (ECL)
Logic threshold:1.5V (TTL), -1.3V
(ECL), ground (0V).
Format: NRZ
Termination: Nominal TTL into 75
to ground or nominal ECL into75 to -
2V
Return loss: Typically >15 dB, 500
kHz to 200 MHz (TTL)
Binary Clock Input
Clock rates: 700 kb/s to 50 Mb/s
(TTL), 700 kb/s to 170 Mb/s (ECL)
Logic threshold:1.5V (TTL), -1.3V
(ECL), ground (0V), signal mean level.
Format: Nominal squarewave 60/40 to
40/60 duty cycle.
Termination: Nominal TTL into 75
to ground or nominal ECL into75 to
-2V
Return loss: Typically >15 dB, 500
kHz to 100 MHz (TTL)
Binary interface rates: 2, 8, 34 and
140 Mb/s if Option UKJ is fitted. 0.7, 2,
8, 34and 140 Mb/s if Option UKK is
fitted.
Frequency measurement: On
external clock input and binary clock
input.
Jitter generation: Simultaneous jitter
of binary clock and binary data outputs
if Option UHK or A3K (2, 8, 34 & 140
Mb/s) is fitted.
Jitter measurement: Jitter
measurement of binary clock input if
Option UHN, A1M, A1N, A1P, A3L,
A3V or A3N (2, 8, 34 & 140 Mb/s
±100 ppm) is fitted.

Table of Contents

Other manuals for HP 37717C

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HP 37717C and is the answer not in the manual?

HP 37717C Specifications

General IconGeneral
BrandHP
Model37717C
CategoryMeasuring Instruments
LanguageEnglish

Related product manuals