Icom IC-7610 Basic Manual

1
PANEL DESCRIPTION
1-3
q DC POWER SOCKET [DC 13.8 V]
Connects to 13.8 V DC through the DC power
cable.
w TUNER CONTROL SOCKET [TUNER]
 Acceptsthecontrolcablefromanoptional
AH-4 orAH-740
automatic antenna tuner.
e COOLING FAN
 CoolsthePAunitwhennecessary.
r GROUND TERMINAL [GND]
 Connectstogroundtopreventelectricalshocks,
TVI,BCIandotherproblems.
t ANTENNA CONNECTOR [ANT1]/[ANT2]
 Connectstoa50Ωantenna.IfyouusetheAH-4or
AH-740,youmustconnecttheantennato[ANT1].
y ALC INPUT JACK [ALC]
 ConnectstotheALCoutputjackofanon-Icom
linearamplier.
u SEND CONTROL JACK [SEND]
 Connectstocontroltransmitwithnon-Icomexternal
units.
i EXTERNAL SPEAKER JACK A/B [EXT-SP]
 Acceptsa4~8Ωexternalspeaker.
o USB PORT [USB 1] (Type B)
Connects to a PC for remote control operations.
!0 USB PORT [USB 2] (Type B)
For digital data input or output.
!1 EXTERNAL DISPLAY CONNECTOR
[EXT-DISPLAY]
 Connectstoanexternaldisplaymonitor.
!2 ETHERNET CONNECTOR [LAN]
 ConnectstoaPCnetworkthroughaLAN.
!3 TRANSVERTER CONNECTOR [X-VERTER]
Connectstoanexternaltransverterforinput/output.
!4 REFERENCE SIGNAL INPUT [REF IN]
 Inputfora10MHzreferencesignalthroughthe
BNC connector.
!5 RECEIVE ANTENA [RX ANT–IN]/[RX ANT–OUT]
Connectstoanexternalunit,suchaspreamplier
orRFlter,usingBNCconnectors.
• This is located between the transmit/receive switching
circuit and receiver’s RF stage.
!6 CI-V REMOTE CONTROL JACK [REMOTE]
Connects to a PC or other transceiver for remote
control.
!7 METER JACK [METER]
 Outputsreceivedsignalstrength,transmitoutput
power,VSWR,ALC,speechcompression,V
d or Id
levelsforanexternalmeter.
!8 EXTERNAL KEYPAD JACK [EXT KEYPAD]
(p. 13- 4)
 Connectstoanexternalkeypadfordirectvoice
memory,memorykeyer,RTTYmemoryorPSK
memory transmission.
!9 STRAIGHT KEY JACK [KEY]
 Connectstoastraightkey,paddle,oranexternal
electronic keyer with 6.35 mm (¼ in) stereo plug.
@0 ACC SOCKET [ACC1]/[ACC2]
 Connectstodevicestocontrolanexternalunitorto
control the transceiver.
Rear panel
q ew r
!5
!4
!3 !2 !1 o i
y
!7 !8 !9!6
@0
t
u
!0

Icom IC-7610 Specifications

General

Receiver Type	Direct sampling
Number of Antenna Connectors	2
Type	HF/50 MHz Transceiver
IF DSP	Yes
Antenna Connector	SO-239
Frequency Range	0.030–60.000 MHz
Power Supply	13.8 V DC ±15%
Modes	AM, FM
RF Output Power	100 W
Display	7-inch color
Weight	8.5 kg
External Speaker Connector	3.5 mm
USB Connector	Type B
Output Power	100 W
Operating Temperature	-10°C to +60°C