Icom IC-7610

8
SET MODE
8-2
Tone Control
MENU
» SET > Tone Control > RX > SSB
RX HPF/LPF (Default: – – – – – – – – –)
Sets the cut-off frequencies for the receive audio high-
pass lter and low-pass lter in 100 Hz steps, in the
SSB mode.
L If this item is set, the “RX Bass” and “RX Treble”
items are automatically set to “0.”
RX Bass (Default: 0)
RX Treble (Default: 0)
Sets the bass or treble level of the receive audio.
MENU
» SET > Tone Control > RX > AM
RX HPF/LPF (Default: – – – – – – – – –)
Sets the cut-off frequencies for the receive audio high-
pass lter or low-pass lter in 100 Hz steps, in the AM
mode.
Selectable ranges:
L If this item is set, the “RX Bass” and “RX Treble”
items are automatically set to “0.”
RX Bass (Default: 0)
RX Treble (Default: 0)
Sets the bass or treble level of the receive audio.
MENU
» SET > Tone Control > RX > FM
RX HPF/LPF (Default: – – – – – – – – –)
Sets the cut-off frequencies for the receive audio high-
pass lter or low-pass lter in 100 Hz steps, in the FM
mode.
L If this item is set, the “RX Bass” and “RX Treble”
items are automatically set to “0.”
FM RX Bass (Default: 0)
FM RX Treble (Default: 0)
Sets the bass or treble level of the receive audio.
MENU
» SET > Tone Control > RX > CW
MENU
» SET > Tone Control > RX > RTTY
MENU
» SET > Tone Control > RX > PSK
RX HPF/LPF (Default: – – – – – – – – –)
Sets the cut-off frequencies for the receive audio high-
pass lter or low-pass lter in 100 Hz steps in the CW,
RTTY, and PSK modes.
MENU
» SET > Tone Control > TX > SSB
TX Bass (Default: 0)
TX Treble (Default: 0)
Sets the bass or treble level of the transmit audio.
TBW (WIDE) (Default: 100 – 2900)
TBW (MID) (Default: 300 – 2700)
TBW (NAR) (Default: 500 – 2500)
Sets the transmission pass bandwidth to wide, mid,
or narrow, by changing the lower and higher cut-off
frequencies.
MENU
» SET > Tone Control > TX > AM
TX Bass (Default: 0)
TX Treble (Default: 0)
Sets the bass or treble level of the transmit audio .
MENU
» SET > Tone Control > TX > FM
TX Bass (Default: 0)
TX Treble (Default: 0)
Sets the bass or treble level of the transmit audio .
Function
MENU
» SET > Function
Beep Level (Default: 50%)
Sets the beep output level.
L If the “Beep (Conrmation)” item is set to “OFF,” no
beeps sound.
Beep Level Limit (Default: ON)
Selects whether or not to limit the volume up to the
specied level.
Beep (Conrmation) (Default: ON)
Turns the Conrmation beep ON or OFF.
L If the “Beep Level” item is set to “0%,” no beep sounds.
Band Edge Beep (Default: ON (Default))
Turns the Band Edge beep ON or OFF.
InformationL
• If the “Beep Level” item is set to “0%,” no beep sounds.
• When you tune into an amateur band’s frequency
range, the high Band Edge beep sounds.
• When you tune out of an amateur band’s frequency
range, the low Band Edge beep sounds.