Icom IC-V86 - Resetting the Transceiver

53 pages

Save Page as PDF

To Next Page

To Previous Page

11-1

Section

Resetting ..............................................................................................11-2

RESETTING

Main Page

Introduction2
Features2
Accessories3
Supplied Accessories4
Belt Clip4
Antenna4
To Attach the Belt Clip4
Battery Pack or Case5
Jack Cover5
To Attach the Battery Pack or Case5
To Remove the Battery Pack or Case5
Battery Charge6
Using the BC-191 to Rapid Charge the BP-2647
Charging Time8
Optional Battery Case (BP-263)9
Table of Contents10
Advanced Operation10
Section 3 ADVANCED OPERATION11
Adjusting the Audio Level11
Selecting Passband Width11
Receiving11
Transmitting11
[VOL] Function Assignment12
Weather Channel Operation (for Only the USA Version)13
- D Weather Channel Selection13
- D Weather Alert Function13
- Repeater and Duplex Operation14
- Accessing a Repeater15
  - Turning on the Subaudible Tone Encoder15
  - Setting the Shift Direction of the Transmit Frequency15
- Section 4 REPEATER and DUPLEX OPERATION15
- DTCS Encoder (Only TX)16
- Lockout Function16
- Auto Repeater Function (for Only the USA Version)17
  - Frequency Range and Offset Direction17
  - Memory/Call Operation18
- General Description19
- Copying Memory/Call Contents19
- Section 5 MEMORY/CALL OPERATION19
- D Memory/Call Channel to VFO19
- D Memory/Call to Memory/Call20
- Clearing Memory Contents21
- Display Type22
  - Frequency Display22
  - Channel Number Display22
  - Channel Name Display22
- D Setting the Display Type23
- D Programming a Channel Name23
- D Selectable Characters23
  - Scan Operation24
  - Scan Types25
  - VFO Scan25
  - Memory Scan25
  - Priority Watch25
  - Setting Skip Channels26
  - Scan Resume Setting26
  - Tone Squelch and Pocket Beep27
  - Tone/Dtcs Squelch28
  - Recommended CTCSS Tones28
  - Recommended DTCS Tones28
  - Setting DTCS Polarity28
  - Squelch Burst29
  - Pocket Beep Function30
  - Tone Scan31
  - Dtmf Memory32
  - Programming a DTMF Code Sequence33
  - Programming Mode Indication33
  - DTMF Code Assignment33
  - Transmitting a DTMF Code34
  - Manual DTMF Code Transmission34
  - Using a DTMF Memory Channel34
  - DTMF Memory Channel Number Assignment34
  - Monitoring a DTMF Memory35
  - Setting DTMF Transfer Speed35
  - Set Modes36
- Set Mode Programming37
- Set Mode Items37
- DTCS Code37
- Section 9 SET MODES37
- D Set Mode Operation37
  - Tuning Step38
  - TX Permission38
  - Weather Alert (for Only the USA Version)38
  - VOX Time-Out Timer39
  - DTMF TX Key39
  - Mode39
- Initial Set Mode Programming40
- Initial Set Mode Items40
- Auto Repeater (for Only the USA Version)40
- D Initial Set Mode Operation40
  - Lockout41
  - Squelch Delay41
  - LCD Contrast41
  - Power Save41
  - Select Speed42
  - Microphone Simple Mode42
  - Voltage Indication42
  - Battery Protection Function42
  - Programming43
  - Programming Operation44
  - Programming between Two Transceivers44
  - Programming Using a PC44
  - Resetting45
  - All Reset46
  - Troubleshooting48
  - No Power Comes on48
  - No Sound Comes from the Speaker48
  - Transmitting Is Impossible48
  - Options49
  - Battery Pack/Battery Case50
  - Antennas50
  - VOX Function51
  - Optional Unit Connection51
  - Turning the VOX Function on or off51
  - Jack Cover51
  - VOX-Related Settings52
  - VOX Gain52
  - VOX Delay52

Icom IC-V86 - Resetting the Transceiver

Table of Contents

Related product manuals