Iseki TH4365 - Pre-Delivery Inspection

ASSEMBLY & PRE-DELIVERY INSPECTION
1
07
P
RE-DELIVERY INSPECTIO
N
-
C
heck that batter
y
is char
g
ed enou
g
h.
- Check that en
g
ine oil level is correct.
-
C
heck that coolant level is correct.
-
C
heck
f
an belt tension, 14mm de
f
lection, when sub-
j
ected to a
f
orce o
f
thumb pressure.
(
10k
gf)
-
C
heck that transmission oil level is correct.
- Fill in
a
suff
i
c
i
e
nt
a
m
ou
nt
of
N
o
.2
d
i
ese
l
fue
l t
o
co
m-
p
lete pre-deliver
y
service.
- Ensure clean and ti
g
ht cable connections at batter
y
.
Batter
y
must be securel
y
mounted.
- Check air cleaner, element, hoses, and clamps for
co
rr
ec
t in
s
t
a
ll
a
ti
o
n.
- Check brake pedal linka
g
e for correct free-pla
y
.
- Check steerin
g
and brake linka
g
e cotter pins and
loc
k n
u
t
s
f
o
r
secu
r
e
in
s
t
a
ll
a
ti
o
n.
- Check filter element and, all connections and
c
lamps for h
y
draulic pump and filter
.
-
O
n 4WD models, check oil level in
f
ront drive axle.
Place fuel filter cock in the “
O
N” position. Take up po-
s
ition in operator
’
s seat and en
g
a
g
e parkin
g
brake.
- Pl
ace
a
ll
s
hi
f
t l
e
v
e
r
s
in n
eu
tr
a
l.
- Place rear PT
O
and mid PT
O
selector levers in
neu
tr
a
l.
NOTE: Engine will not start unless range shift lever
i
s selected to neutral
,
rear PT
O,
and mi
d
P
T
O
selector lever are in neutral.
-
S
et throttle lever at half to full throttle and turn main
s
witch counterclockwise
5
-1
0
.
- Turn main switch clockwise to
“O
N”.
O
il pressure
and alternator warnin
g
li
g
hts will illuminate. Hold in
“O
N” position 1-2 seconds.
- Turn main switch to
“S
TART” to crank the en
g
ine.
R
elease ke
y
to “
O
N” position the moment en
g
ine
s
tarts. Check that warnin
g
li
g
hts
g
o out.
- Allow en
g
ine to warm up to operatin
g
temperature
at about 1500 rpm.
-
O
perate Tractor to con
f
irm it operates smoothl
y
at all speeds includin
g
f
our-wheel drive
(
i
f
so
e
quipped
)
.
-
O
perate PT
O
to see that it functions properl
y
.
-
C
heck that all li
g
hts and instruments operate properl
y
.
- Check brakes for balanced operation.
-
C
heck en
g
ine low idle speed, 980-1020 rpm.
- Check en
g
ine hi
g
h idle speed, 2760-2810 rpm.
- Set throttle lever at idle speed, shut off en
g
ine and
c
heck tractor
f
or coolant, lubricatin
g
oil or
f
uel leaks.
- Check that safet
y
start s
y
stem functions correctl
y
.
- Lubricate all
f
ittin
g
s.
- Check tire inflation pressures.
-
C
heck front wheel toe-in.
- check anti-freeze to see that it is adequate for local
c
lim
a
t
e
co
n
d
iti
o
n.
NOTE: Factor
y
fill is set to -30 F
(
-34 cent-degrees
)
.
- Check to see that all safet
y
decals and safet
y
s
witches are in place.
- Clean and polish sheet metal as necessar
y
.
- Fill
f
uel tank to prevent moisture accumulation.
- Review this
O
perator’s Manual with the customer
when deliverin
g
or demonstratin
g
Tractor.