Jackson AJX Series User Manual (English)

Other manuals for Jackson AJX Series

Installation/Operation & Technical Manual110 pages

Questions and Answers:

D
Donald WellsAug 15, 2025
Why are racks going through the Jackson Commercial Food Equipment, but results are poor?
- W
  wcarpenterAug 15, 2025
  Poor results with racks going through your Jackson Commercial Food Equipment can stem from several issues: * Incorrect detergent quantity for the water volume. Adjust the detergent to the appropriate level. * Clogged strainers/scrap basket. Clean these out. * Ware not being properly pre-scrapped. Review the Ware Preparation section. * Missing end-caps on wash or rinse arms. Verify and replace them as needed. * Low tank heat. See the previous page for solutions. * Inadequate rinse. See the previous page for solutions. * Incorrect voltage. Verify it matches the machine data plate. * Wash pump cavitation due to low water level. Ensure drains are shut and the water level is correct.
M
Madison WallaceAug 18, 2025
How to fix spotting of silverware, glasses, and dishes in Jackson Commercial Food Equipment?
- K
  kelli54Aug 18, 2025
  Spotting on your silverware, glasses, and dishes from your Jackson Commercial Food Equipment can be due to: * Incorrect final rinse temperature. Make sure the rinse water temperature matches the data plate. * Clogged wash and/or rinse nozzles and arms. Remove the arms and clear any debris from them and their nozzles. * Excessively hard water. Consider installing a water softener. * Loss of water pressure due to a clogged/obstructed wash pump. Turn off the power, drain the wash tank, and clear any debris from the pump intake. * Ware not being properly pre-scrapped. Review the Ware Preparation section. * Incorrect detergent/chemical concentrations. Verify the concentrations are correct for the water volume.
C
Christopher SmithAug 21, 2025
What to do if Jackson Commercial Food Equipment machine will not fill?
- K
  Kimberly WhiteAug 21, 2025
  If your Jackson Commercial Food Equipment machine isn't filling, here's what to check: * Ensure water lines are connected to the machine. * Make sure the machine doors are completely closed. * Verify the incoming water solenoid valve is operating; replace it if faulty. * Check the wiring of the floats and ensure no debris is jamming them; replace if necessary.
C
Charlotte DavisAug 25, 2025
Why is there inadequate rinse in my Jackson Commercial Food Equipment?
- D
  daniel46Aug 26, 2025
  Inadequate rinsing in your Jackson Commercial Food Equipment can be caused by: * Low incoming water pressure. Verify incoming water pressure during fill is 15 PSI. * A clogged incoming water solenoid. Check the valve for trapped debris and remove it.
J
Jason GarrettAug 28, 2025
How to troubleshoot low wash arm pressure and poor spray pattern in Jackson Commercial Food Equipment?
- C
  Craig WangAug 28, 2025
  Low wash arm pressure and a poor spray pattern in your Jackson Commercial Food Equipment may result from: * Clogged wash arm nozzles. Clear any debris from the nozzles. * Clogged wash tank or wash pump strainers. Clean out the strainers. * A worn wash pump impeller. Verify the impeller's condition and replace it if needed.
J
John BowmanAug 31, 2025
What causes low wash tank temperature in Jackson Commercial Food Equipment?
- R
  rachel56Aug 31, 2025
  Low wash tank temperature in your Jackson Commercial Food Equipment can be attributed to: * Low incoming water temperature. Verify the incoming water temperature matches the data plate. * The heater not energizing. Verify the wash tank heater is operating and replace it if necessary. * Low incoming voltage. Have an electrician verify the incoming power matches the data plate.
W
William OdomSep 4, 2025
What to do if nothing on Jackson Commercial Food Equipment machine operates?
- B
  brittany23Sep 4, 2025
  If nothing on your Jackson Commercial Food Equipment machine operates, check the following: * Have an electrician verify the machine is wired correctly to the incoming power source. * Reset the machine circuit breaker. If it trips again, contact an electrician to verify the machine amp draw. * Reset the service breaker. If it trips again, contact an electrician to verify the machine amp draw.
J
Jasmine LopezSep 7, 2025
Why is the fill weak in my Jackson Commercial Food Equipment machine?
- B
  bullockjohnSep 7, 2025
  A weak fill in your Jackson Commercial Food Equipment machine can be due to: * Low incoming water pressure. Verify incoming water pressure during fill is 15 PSI. * A clogged incoming water solenoid. Check for and remove any debris trapped in the valve.
O
Olivia HornSep 12, 2025
What causes the pawl bar to not move in Jackson Commercial Food Equipment?
- J
  joshua11Sep 12, 2025
  The pawl bar in your Jackson Commercial Food Equipment might not move because of: * A failed or broken overload spring. Replace the spring if necessary. * No power to the drive motor or a failed drive motor. Verify power and wiring connections to the motor; replace the motor if needed. * Improper installation of the pawl bar. Verify the pawl bar is installed correctly.