Jackson TEMPSTAR User Manual (English)

Other manuals for Jackson TEMPSTAR

Installation & Operation Manual103 pages

Installation And Quick Guide2 pages

Installation Quick Guide2 pages

Questions and Answers:

B
Brian ChoiAug 19, 2025
Why is my Jackson TEMPSTAR not cleaning dishes properly?
- J
  Jenny Oconnor DDSAug 19, 2025
  If your dishes aren't getting clean in your Jackson Dishwasher, it could be due to several reasons. First, check that the incoming water, rinse water, and wash water temperatures meet the minimum requirements listed on the machine's data plate. Also, ensure that the detergent concentration is correctly adjusted for the machine's water capacity. Finally, verify that the solid detergent dispenser canister isn't empty and replace it if needed.
P
Paige JacksonAug 21, 2025
What to do if my Jackson Dishwasher runs continuously in the wash cycle?
- T
  Tanya ChambersAug 21, 2025
  If your Jackson Dishwasher is running continuously in the wash cycle, first check if the machine is in Delime mode and flip the NORMAL/DELIME switch to NORMAL mode. If it is not in Delime mode, verify that the timer is rotating. If the timer is not rotating, check to see that the motor is receiving power. If the motor is receiving power, replace the motor and/or timer assembly. Also, inspect the cam timer for any obstructions and remove them if present.
D
deborah18Aug 23, 2025
What to do if my Jackson TEMPSTAR will not fill after closing the door but the power light is on?
- D
  Dale HernandezAug 23, 2025
  If your Jackson Dishwasher isn't filling after you close the door, but the power light is on, the issue might be with the rinse solenoid valve, the door switch, or the high-level probe. Try these steps: * Repair or replace the rinse solenoid valve if needed. * Check the wiring of the door switch and replace the switch if the wiring is correct. * Inspect the high-level probe and clean it if it's fouled. If it's clean but still not working, replace it.
R
Ryan NelsonAug 26, 2025
What to do if my Jackson TEMPSTAR Dishwasher won't drain when I press the power button?
- K
  Kelsey HowardAug 26, 2025
  If your Jackson Dishwasher isn’t draining when you press the power button, there are a few things to check. First, make sure the drain isn’t clogged by removing any obstructions. Next, ensure that the standpipe has been removed before running the drain cycle again. Finally, if neither of those solutions works, the drain valve may be defective and need replacement.
J
James SheltonAug 28, 2025
Why is my Jackson TEMPSTAR not reaching the required wash or rinse temperature?
- L
  laurencummingsAug 28, 2025
  If the wash water in your Jackson Dishwasher isn't reaching the required temperature, the issue could be a faulty wash heater, misadjusted or faulty thermostats, or a defective wash thermometer. Check the wash heater element for continuity; if it's open, replace the heater. Verify the operation and setting of the thermostats, and replace them if necessary. Replace the wash thermometer if it is defective.
R
Rachel MillerAug 30, 2025
Why is my Jackson TEMPSTAR Dishwasher not reaching the required rinse temperature?
- T
  Troy AndradeAug 30, 2025
  If the rinse water in your Jackson Dishwasher isn't reaching the required temperature, it could be due to a faulty rinse heater. Check the element for continuity; if it's open, replace the heater. It may also be caused by misadjusted or faulty thermostats; verify their operation and settings, and replace them if necessary. Another potential cause is a defective rinse thermometer, which should be replaced.
F
fkennedySep 1, 2025
What to do if my Jackson TEMPSTAR Dishwasher will not run, but the power light is on and it is filling?
- E
  eric63Sep 1, 2025
  If your Jackson Dishwasher isn't running after closing the door, but the power light is on and it's filling, it could be due to a faulty timer, a faulty or damaged wash motor, or a faulty wash motor contactor. Check that the timer is receiving power; if it is, replace the timer assembly. Verify that the wash motor is getting power; if it is, replace the motor. Check the wash motor contactor for continuity; if the contacts are open, replace the contactor.
J
James DuncanSep 3, 2025
How to fix weak rinse or slow fill in my Jackson Dishwasher?
- J
  Jenna CarterSep 3, 2025
  If your Jackson Dishwasher is filling slowly or the rinse is weak, it might be due to clogged rinse arms, low incoming water pressure, or a clogged Y-strainer. Remove and clean the rinse arms. Adjust the water pressure regulator to ensure a 10A5 PSI flow. Clean out the Y-strainer.
D
David AndrewsSep 6, 2025
What to do if my Jackson TEMPSTAR Dishwasher will not fill after closing the door and the power light is not illuminated?
- N
  Nicholas MontoyaSep 6, 2025
  If your Jackson Dishwasher isn't filling after you close the door and the power light isn't illuminated, it could be due to a tripped service breaker, the machine not being connected to a power source, or a faulty power source. Reset the service breaker. If it trips again, contact an electrician to check the machine's amp draw. Verify that the machine is properly connected to the power source. Check the wiring of the power switch and replace the switch if the wiring is correct.
S
Susan BarnesSep 8, 2025
How to fix doors that won't close completely on my Jackson TEMPSTAR?
- D
  David HammondSep 8, 2025
  If the doors on your Jackson Dishwasher won't close completely, it could be due to improper spring tension, an obstruction in the door channel, or the doors not being square with the frame. Adjust the spring tension by loosening (but not removing) the spring bolt nuts, adjusting the tension, and then tightening the nuts back. Remove any obstruction in the door channel. Adjust the frame to accommodate the doors.