Page 10
Solar Heat
The SOLAR HEAT selection controls solar heating. A solar heating system and optional solar sensor are required for
SOLAR HEAT selection to operate.
To use Solar Heat
Highlight SOLAR HEAT and press SELECT. Use the SELECT button to turn SOLAR HEAT on or off.
HEAT PUMP: If a Heat Pump is properly connected to this system, HEAT PUMP will appear on the screen in place of
SOLAR HEAT.
If a solar sensor is not installed, EXTRA AUX replaces SOLAR HEAT and may be used to control an auxiliary (see
"Auxiliary Equipment" to turn on or off EXTRA AUX).
For solar heating to take place, the SOLAR HEAT (in EQUIPMENT ON/OFF) must be enabled, also the filter pump
must be on. Solar temperature must be at least 5° F above the water temperature and the water must be cooler than the
thermostat setting.
If no Solar Sensor
is installed, EXTRA
AUX will appear as a
menu item.
FILTER PUMP ON
SPA
POOL HEAT
SPA HEAT
SOLAR HEAT
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
FILTER PUMP ON
SPA
POOL HEAT
SPA HEAT
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
SOLAR HEAT
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ENA
FILTER PUMP ON
SPA
POOL HEAT
SPA HEAT
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
AUXEXTRA
FILTER PUMP ON
SPA
POOL HEAT
SPA HEAT
SOLAR HEAT
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
SPA HEAT
ENABLED
SET TO 102°F
Use ARROW KEYS
to set value.
Press SELECT
to continue.
FILTER PUMP ON
SPA
POOL HEAT
SOLAR HEAT
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
SPA HEAT
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
FILTER PUMP * * *
POOL HEAT
SPA HEAT
SOLAR HEAT
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
SPA
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
FILTER PUMP OFF
POOL HEAT
SPA HEAT
SOLAR HEAT
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
SPA
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
SPA WILL
TURN ON
AFTER DELAY
Spa Heat
The SPA HEAT enables the heater for the spa. When the LED is green, the heater is enabled. When the LED is red,
the heater is on and firing. It uses the settings from SET TEMP menu, or you can increase/decrease when enabling.
To use Spa Heat
Highlight SPA and press SELECT. The spa will come on after a short delay. Highlight SPA HEAT and press SELECT.
Use the UP/DOWN arrow keys to set the desired temperature and press SELECT.
To Next Page
Loading...
Need help?
General
