What happens if I hesitate too long while quilting with my Janome Quilt Maker Pro 18 VERSA?
Move more quickly so stitches don’t overlap or build up. When starting the machine, begin moving fabric immediately. Sewing in one place too long will cause the thread to break.
What type of needle should I use with my Janome Quilt Maker Pro 18 VERSA?
Use only the needles recommended by Janome (134, sizes 12 through 21).
General| Automatic Needle Threader | Yes |
|---|---|
| Speed Control | Yes |
| LCD Screen | Yes |
| USB Port | Yes |
| Lighting | LED |
| Stitch Regulation | Yes |
| Drop Feed | Yes |
Provides essential rules and precautions for performing service on the machine.
Specifies the dimensions of the sewing area.
Details the sewing speed capabilities in different modes.
Defines the range of stitches per inch supported by the machine.
Identifies the type and size of needles used.
Describes the type of hook mechanism used in the machine.
Specifies the type of bobbin compatible with the machine.
Identifies the type of bobbin case used.
States the type of motor powering the machine.
Explains the needle's movement and stitch positioning.
Details the machine's power requirements and specifications.
Lists the lubricants for major machine parts.
Specifies the lubricant for the hook assembly.
Torque specifications for 4mm socket head cap screws.
Torque specifications for 4mm set screws.
Torque specifications for 5mm socket head cap screws.
Torque specifications for 5mm set screws.
Torque specifications for 6mm socket head cap screws.
Torque specifications for 6mm set screws.
Lists different lubricant types and their specific machine component applications.
Provides order numbers for individual lubricants and repair kits.
Outlines the recommended frequency for machine lubrication.
Verifies the thread mast is centered over spool pins for proper thread feed.
Details how to check and adjust the gap between the machine frame and hand wheel.
Inspects thread guides, stirrup, and needle bar guide for defects.
Lists required tools and emphasizes unplugging the machine before starting.
Detailed instructions for detaching the front cover and its components.
Procedure for safely disconnecting cables from the control board.
Details where to apply Lube #1 (Red) and Lube #2 (Blue) on bearings.
Specifies the application of Lube #6 (Purple) to the bobbin case raceway.
Details lubrication for needle bar, presser bars, and hopping foot.
Specifies lubrication for inside caged needle bearings.
Details lubrication for the presser bar slide and plunger.
Checks screws on the Pitman crank and take-up lever for firm fixing.
Verifies timing pulleys are securely fixed on their shaft flats.
Guides setting the counterweight timing for the main shaft.
Explains the 120-degree rule for screw placement on timing components.
Details the adjustment of the hook-shaft timing pulley.
Provides critical information about hook-shaft pulley settings and axial play.
How to check and adjust axial play in the main shaft.
How to check and adjust axial play in the hook shaft.
Verifies the base plate sits flat on a surface.
Explains using shim washers for base plate adjustment.
Details how to check the timing belt tension by pressing the belt.
Step-by-step guide to adjust the motor drive belt tension.
Emphasizes correct placement of the tensioner washer.
Explains the KinetiQuilt hopping mechanism and its benefits.
Specifies the factory setting for the presser bar height.
How to adjust the hopping foot adaptor for proper stitch formation.
Stresses the need for correct hopping foot adaptor setting before this step.
How to check the presser bar height relative to the needle plate.
Step-by-step guide for adjusting the presser bar height.
Cautionary note regarding improper tightening of the jam nut.
Highlights the critical nature of accurate needle positioning.
Checks needle straightness and centering in the needle plate.
Procedure for adjusting the needle position along the Y-axis.
Procedure for adjusting the needle position along the X-axis.
Adjusting the left side of the head frame for needle position.
Explains the significance of loop lift and needle distance timing.
Lists specialized tools needed for timing adjustments.
Detailed steps to check loop lift and needle distance.
Explains why the bobbin basket must be rotated down for adjustment.
Step-by-step guide to rotate the bobbin basket.
Provides important tips and warnings before timing adjustments.
Step-by-step procedure for setting loop lift and needle distance.
How to slide the hook axially for correct needle distance.
Guidance on tightening hook screws after adjustments.
Re-checking loop lift and needle distance after tightening.
Emphasizes the correct needle height for proper stitch formation.
How to check the needle height relative to the hook point.
Step-by-step guide to adjust the needle bar height.
Warning against completely loosening the needle bar clamp screw.
Verifies the clearance between the stop-finger and bobbin case basket.
Step-by-step guide to adjust the stop-finger clearance.
How to check needle height using the specialized cylinder tool.
Procedure for adjusting needle height with the cylinder tool.
Sighting through the needle eye to compare with the cylinder tool groove.
Reinstalling the hook and checking loop lift and needle distance.
Details the voltage and frequency requirements for machine operation.
Explains the sensor disk and its role in speed and needle position feedback.
Describes how green LEDs indicate the sensor's working status.
Troubleshooting steps for a "Needle Sense Failure" error message.
Troubleshooting for premature motor full speed in manual mode.
Describes the 48V DC power supply's location and role.
Outlines signs indicating a failed power supply.
Details the 48V DC output cable connections to the motor driver and control board.
Identifies the control board's location and its eight main connections.
Lists the connections on the control board that are not used.
Describes the initial LED sequence and the heartbeat LED function.
Details the function of each of the 8 LEDs on the control board.
Explains the two green LEDs indicating 18V and 5V power status.
Steps to diagnose issues if power LEDs are not illuminated.
Conditions under which tension calibration is recommended.
Procedure for calibrating the top tension device.
Specifies the location of the machine's fuse.
Identifies signs indicating a blown fuse.
Instructions on how to initiate the machine's burn-in mode.
How to shut off the machine's burn-in mode.
Explains the functions of buttons in Manual Mode on the touch screen.
Describes the function of the Pause/Play button on the touch screen.
Explains the My Speed indicator and its relation to pedal input.
Details the My Speed and Preset controls for speed adjustment.
How to save and use preset sewing speeds.
Instructions for using the basting mode with timed stitches.
How to adjust and set the top tension using the touch screen.
Explains the low bobbin alarm and thread estimation feature.
How to set the needle to stop in the up or down position.
Using arrow buttons for tie-off, basting, and needle positioning.
How to adjust stitches per inch (SPI) in Regulated Mode.
Describes the four basting stitch settings available.
Explains how Precision mode works, requiring fabric movement to start.
Details Cruise mode, where stitching starts immediately upon pedal press.
How to adjust the Cruise speed setting.
Explains the low bobbin alarm for estimating thread remaining.
Functions for tracking quilting time and stitch counts.
Information on setting and managing machine alarms.
How to select and adjust LED light ring and bar brightness.
Accessing and using the on-screen calculator.
Overview of the diagnostics tests available for the machine.
How to change the display language of the machine.
Procedure for updating machine firmware and display code via USB.
How to record and estimate bobbin thread usage.
Steps to save bobbin thread capacity presets.
Procedure for setting up a new bobbin and alarm.
How to use the timer to track quilting time.
How to use the stitch counter and view lifetime counts.
How to enable and set the overspeed alarm.
How to set the timer alarm as a reminder.
Adjusting brightness for LED light ring and bar.
Overview of the six-function calculator operations.
Lists the six different diagnostic tests available.
Procedure to test the motor sensor for proper operation.
Procedure to test the speed sensor's accuracy.
Checks the movement sensors for stitch regulation.
Tests the functionality of the needle position sensor.
Procedure for calibrating the tension device.
How to test the foot pedal's responsiveness.
Steps to change the machine's display language.
Procedure for updating machine firmware and display code via USB.
Explains the lifetime stitch counter and its use for maintenance.
Interpreting icons for foot controller and sensor connectivity.
Information on board, firmware, display, and sensor version numbers.
Advice on choosing high-quality threads for quilts.
Recommendations for needle sizes based on thread and fabric.
Basics of free motion quilting and operator control.
Basic checks for power, cable connections, and machine reset.
Addresses causes like needle issues and improper installation.
Solutions for issues related to needle size and thread tension.
Correcting problems from improper threading or needle/hook alignment.
Correcting needle position, installation, and damage.
Solutions for needle hitting plate or puckered stitches.
Addressing issues with needle size and overall stitch quality.
Solutions for bobbin case problems and fast quilting speed.
Addressing poor tension due to lint under the tension spring.
Resolving hand wheel issues and thread locks.
Solutions for bobbin tangles and motor failure.
Addressing thread breaks and unbalanced top/bobbin tensions.
Correcting threading errors and cleaning tension discs.
Solutions for wrong needle type and hesitating during quilting.
Addressing needle/hook issues and throat plate damage.
Troubleshooting when the display is not visible due to cable issues.
To Next Page