JR XP810-3 User Manual

www.modelflight.com.au – World’s best source of JR products
4
.
1
3 Pro
g
rammable Mixin
g
(
1-6
)
(
Function Mode
)
, cont.
Exponential Function
A
n exponential function allows you to "smooth" the selected
cur ve. With the cursor at the “point” position, press the left or
right CH key until EXP is indicated. Exponential is activated by
pressing either the + or - key (Refer to figure 4 .1 3C).
Standard Pro
g
rammable Mixin
g
(
3-6
)
Mixing with
T
rim
Whenever the master channel is aileron, elevator , rudder , or
throttle, you have the option of allowing the master channel’ s trim
lever to mix into the slave channel. The Mixing with T rim
Function is always activated in Program Mixes 5 and 6 .
Y ou can observe the operation by watching the slave channel
while moving the master channel’
s trim lever .
For switch assignments refer to Char t 4 .1 3B on the preceeding
page. Deter
mine the master and slave channels required for
mixing. Using the UP - DN keys, select PROG.Mix3. Using the
SEL key , position the cursor next to the channels being mixed.
Using the left or right CH keys, position the cursor under the
master/slave channel, and using the + or - keys, select the
master and slave channels to be used for mixing.
Using the SEL key , position the cursor next to Rate:. T o establish
the mixing value, move and hold the master channel control (up,
down, left, or right) and set the slave servo mix value by
pressing either the + or - keys. T o reverse the direction of the
slave mix, press the opposite of the + or - key until the value of
the mix is set in the reverse direction.
Establishing Of fset
The purpose of the mixing of fset is to redefine the neutral
position of the slave channel. Any desired position may be set
for the of
fset reference point. Pressing the SEL key , position the
cursor to Of
fset:. Deter mine the master channel and move the
master channel control stick to any desired position. Press the
CLR key to memorize this position. The offset value (of
fset value
from ser
vo travel center) is now deter mined; however, the
reference point mixing value is zero.
Include Mixing
When the master channel’s operating value is combined with
another programmed value, it’s called including mixing. For
example, MIX 1 is aileron to elevator
, MIX 5 is elevator to
rudder , MIX 5’ s elevator operating value is included and MIX 1’ s
aileron and elevator value includes the rudder value also.
Functions Related to Program Mixing
• When using aileron, elevator or rudder for the master channe
l
and dual rate/exponential is selected, mixing also includes dua
l
rate and exponential.
• When selecting flaps for the master channel, flap operations
are dif ferent, depending on mixing.
• During snap roll operations, Programmable Mixing Function
2, 4, 5, and 6 are inhibited when the master or slave channels
are aileron, elevator , or rudder . In Programmable Mix 5 and 6
when the master channel is aileron, elevator or rudder, Include
Mixing is activated.
• By using Programmable Mix 5 or 6, the elevator can be
operated using two ser vos because the T rim Function is
activated.
Master channel
Slave channel
THRO:
Throttle
AILE:
Aileron
ELEV:
Elevator
RUDD:
Rudder
GEAR: Retract gear
FLAP:
Flap (AUX1)
SPOI:
Spoiler (AUX2)
AUX3: Extra Channel (AUX3)
Mixing value (max
± 125%)
Mixing switch
offset value
Press the UP and DN keys
simultaneously to enter/exit
the Function Mode
Press the DN and Select key
s
simultaneously to access th
e
Function Mode List Dis
p
la
y
UP
DN SELECT CH CH CLEAR
To Prog rammab l e
Mixing
To Prog rammab l e
Mixin
g
Press to move
the cursor at
left of screen
Press to selec
t
channels to b
e
mixed
Press either the
+
or - key to activat
e
the mixing functio
n
or select the
mixin
g
switch
Press to reset the valu
e
at the cursor to factor
y
preset position/value o
r
to inhibit mixin
g
A
CRO 49

JR XP810-3 Specifications

General

Brand	JR
Model	XP810-3
Category	Remote Control
Language	English