Home
KEB
Power Supply
combivert R6-S
KEB combivert R6-S Applications Manual
4
of 1
of 1 rating
168 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
Seite 1.3
-
4
COMBIVERT
R6-S
© KEB, 2008-02
Hardware
1.3.1.2
Control board 2B.R6
Connection terminals of the control board
X2A.10...23
X2A.24...29
X1B
X2C
X2B
X4B
5
4
3
2
1
9
8
7
6
5
4
3
2
1
9
8
7
6
X1B
Connection precharging
Net Potential
!
X2B
Connection synchronization line
X2C
Activation of the line contactor self-holding
X4B
HSP5 interface
No direct PC connection!
X2A
Control terminal strip
Install control and mains
cable se-
parately
!
17
19
Table of Contents
Introduction
3
Introduction
2
Table of Contents
3
Introduction
4
Use of Power Supply and Regenerative Units
11
Functional Principle
12
Part Code
13
Hardware
15
Control Board 1B.R6
17
Control Boards
17
Control Board 2B.R6
18
Control Terminal Strip X2A
19
Activation of the Self-Holding X2C
21
HSP5 Operator Interface X4B
21
Synchronization Line X2B
21
Connection for Precharging X1B
22
Connection of the Control Release of the Connected Inverter
22
Operation
25
Fundamentals
25
Parameters, Parameter Groups, Parameter Sets
25
Adjustment of Parameter Values
26
Selection of a Parameter
26
Acknowledge of Feedbacks
27
ENTER Parameters
27
Not Set-Programmable Parameters
27
Reset of Error Messages
27
Reset of Peak Values
27
Password Structure
29
Password Levels
30
Passwords
32
Network Components
35
Functions
35
Parameter Overview
40
Functions
41
Analog Outputs
67
Digital In- and Outputs
72
Digital Inputs in PNP Control (DI.00)
74
Set Digital Inputs Per Software (DI.01, DI.02)
74
Input Terminal State (Ru.21), Internal Input State (Ru.22)
75
Digital Noise Filter (DI.03)
76
Input Trigger (DI.05)
76
Invert the Inputs (DI.04)
76
Strobe-Dependent Inputs (DI.06, DI.07, DI.08)
76
Assignment of the Inputs
78
Reset / Input Selection (DI.09) and Neg. Slope for Reset Inputs (DI.10)
78
Software-ST and Locking of the Control Release
80
Conditions (Do.00
83
AND/OR Connection of the Conditions (Do.24)
85
Operating Mode
91
Invert Conditions for Flags 0
85
Selection of the Conditions for Flags 0
85
Protective Functions
96
Error and Warning Messages
97
Undervoltage
98
Overvoltage
98
Overcurrent
98
Overload
99
Inverter Overtemperature
99
External Fault
99
Bus Error
100
Set Selection Error
100
Hardware Error
100
Regeneration Error
101
Response to Malfunction Messages
101
Selection of the Response
101
General Fault Reset (Pn.15)
102
Automatic Restart
103
Undervoltage Error (E.UP)
103
Overvoltage Error (E.OP)
103
Overcurrent Error (E.OC)
103
Malfunction Messages and Pre-Warnings
103
Special Functions
104
Parameter Sets
106
Indirect and Direct Set-Addressing
107
Not Set-Programmable Parameters
107
Security Parameters
107
Copy Parameter Sets Via Bus (Fr.01, Fr.09)
109
Locking of Parameter Sets
114
Parameter Set Activation Delay/ Deactivation Delay (Fr.05, Fr.06 )
114
Start-Up
133
Installation and Connection
133
Safety Instructions
134
Start-Up
138
Project Design
145
Error Assistance
147
Troubleshooting
147
Status Messages
147
Warning Messages
149
Annex
151
Project Design
153
Other manuals for KEB combivert R6-S
Instruction Manual
56 pages
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the KEB combivert R6-S and is the answer not in the manual?
Ask a question
KEB combivert R6-S Specifications
General
Brand
KEB
Model
combivert R6-S
Category
Power Supply
Language
English
Related product manuals
KEB COMBIVERT R5-C
28 pages
To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...
Need help?
General
