What to do if Kodak EasyShare DX4530 Digital Camera displays 'Card is protected (Reset switch on card)'?
If your Kodak Digital Camera displays 'Card is protected (Reset switch on card)', it means that the switch on the SD card is in the write-protect position. Reset the switch as shown on the camera screen.
Why are my pictures too dark on Kodak EasyShare DX4530?
If the pictures taken with your Kodak Digital Camera are too dark, there could be several reasons. First, the flash might not be on or did not function; turn on the flash. Second, the subject might be too far away for the flash to have an effect; move closer to the subject. Third, the subject might be in front of a bright light, in which case you should use Fill flash or change your position. Finally, the lighting condition might be too dark; increase Exposure Compensation or Long Time Exposure.
Why picture is not clear on Kodak EasyShare DX4530?
If the pictures taken with your Kodak Digital Camera are not clear, it could be due to several reasons. The lens might be dirty, so clean the lens. The subject might be too close, so move further away. The subject or the camera might have moved during the shot, so hold the camera steady. The subject might be too far for the flash, so move closer.
Why pictures are not transferred to the computer from Kodak Digital Camera?
If pictures are not transferred to the computer from your Kodak Digital Camera, ensure that the AC adapter or USB cable is securely connected. Also, verify that the necessary software is installed. If the issue persists, restart the computer and try again. If using a camera dock, ensure the camera was not removed during picture transfer; replace the camera on the camera dock and press the Connect button. Finally, ensure that the Connect button was pressed.
Why Kodak Digital Camera displays 'Record in internal memory (Card speed is slow)'?
If your Kodak Digital Camera displays 'Record in internal memory (Card speed is slow)', it means that the card cannot be used in the camera. Change the storage location to internal memory.
What to do if Kodak Digital Camera displays 'Other error code'?
If your Kodak Digital Camera displays 'Other error code', it means that an error is detected. Turn the Mode dial off, then back on. If the error appears again, call for service.
Why slide show does not run on external video device with Kodak EasyShare DX4530 Digital Camera?
If the slide show does not run on an external video device with your Kodak Digital Camera, the Video Out setting is incorrect. Adjust the camera Video Out setting (NTSC or PAL).
Why cannot transfer pictures to computer and Add New Hardware Wizard cannot locate drivers for Kodak Digital Camera?
If you cannot transfer pictures to your computer and the Add New Hardware Wizard cannot locate drivers for your Kodak Digital Camera, it means that the software is not installed on the computer. Disconnect the USB cable (if using camera dock, disconnect the cable and remove the camera from the dock), then install the Kodak EasyShare software.
Why ready light does not turn on and Kodak EasyShare DX4530 Digital Camera does not work?
If the ready light does not turn on and the Kodak Digital Camera does not work, it could be due to several reasons. The camera might not be turned on, so turn it on. The batteries might be exhausted, so replace or recharge them. The Mode dial might have been on when batteries were reloaded, so turn the Mode dial off, then back on.
Why does rechargeable Ni-MH battery pack has a short life on Kodak EasyShare DX4530 Digital Camera?
If the rechargeable Ni-MH battery pack in your Kodak Digital Camera has a short life, it could be due to dirt on the battery contacts. Wipe the battery contacts with a clean, dry cloth before loading batteries in the camera. Additionally, the battery may need to be conditioned. Place the camera on the camera dock. If you have EasyShare camera dock— When the charge light turns green, remove the camera from the dock. After a minimum of 5 minutes, place the camera back on the dock. If you have EasyShare camera dock II— When all 3 lights turn green, remove the camera from the dock. After a minimum of 5 minutes, place the camera back on the dock Repeat steps 1 and 2 until the combined charge time equals a minimum of 2 hours.
General| Megapixel | 5 MP |
|---|---|
| Sensor type | CCD |
| Digital zoom | 3.3 x |
| Optical zoom | 3 x |
| Combined zoom | 10 x |
| Focal length range | 8 - 24 mm |
| Metering | automatic: multi-pattern TTL-AE |
| Interface | Dock Compatibility - KODAK EASYSHARE Camera Dock I, II and KODAK EASYSHARE Printer Dock 4000 |
| Cable type | 1 x A/V cable, 1 x USB cable |
| Minimum RAM | 64 MB |
| Minimum processor | 233 MHz |
| Dimensions (WxDxH) | 111 x 66 x 39 mm |
| Camera shutter speed | 1/2-1/1700 s |
| Minimum storage drive space | 200 MB |
| Minimum system requirements | CD-ROM USB |
| Focal length (35mm film equivalent) | 38 - 114 mm |
| Viewfinder type | Optical |
| Internal memory | 32 MB |
| Compatible memory cards | mmc, sd |
| Display diagonal | 1.8 \ |
| I/O ports | 1 x USB 1 x composite video/audio output 1 x docking station 1 x DC power input |
| Bundled software | KODAK EASYSHARE Software |
| Self-timer delay | 10 s |
| Tripod mounting supported | Yes |
| Product color | Silver |
| Flash modes | Red-eye reduction |
Weight and Dimensions| Weight | 210 g |
|---|
Detailed view of the camera's front panel components and their labels.
Detailed view of the camera's back panel components and their labels.
Detailed view of the camera's side panel ports and features.
Detailed view of the camera's top and bottom panels, including buttons and sockets.
Instructions for installing the Kodak EasyShare software before connecting the camera.
Step-by-step guide on how to properly insert batteries into the camera.
Explanation of the functions of each mode on the camera's mode dial.
Procedures for setting the camera's date and time for accurate photo metadata.
Crucial details on battery types, life, safety, and handling for optimal camera performance.
Guide for using the camera's automatic mode for simple, point-and-shoot photography.
Instructions on how to use the camera's optical zoom feature to get closer to subjects.
Explains how to use the camera's flash settings for different lighting conditions.
How to select the desired resolution and quality for captured images.
Step-by-step instructions for recording video clips with the camera.
How to navigate and view captured photos and videos on the camera's screen.
Instructions for removing unwanted photos and video clips from the camera.
Method to safeguard specific photos and videos from accidental deletion.
Steps to tag photos for printing, including setting the number of copies.
How to tag photos and videos for easy sharing via email.
Guide to entering the camera's setup menu for customization options.
Process for erasing and preparing storage media for camera use.
Specifies the necessary hardware and software for installing the camera software on Windows.
Detailed instructions for installing the Kodak EasyShare software on a computer.
Steps to connect the camera via USB and transfer photos and videos.
Lists all items included in the Kodak EasyShare camera dock II package.
Instructions on how to charge the camera's rechargeable battery using the dock.
Common problems encountered with the camera and their solutions.
Explains various messages displayed on the camera screen and how to resolve them.
Solutions for issues related to the camera dock II and its connectivity.
Information and steps for contacting Kodak customer support for assistance.
Technical details and specifications of the Kodak EasyShare DX4530 digital camera.
Important advice on camera care, safety precautions, and general maintenance.
Information on how many pictures and videos can be stored on different memory card sizes.
To Next Page