Kodak Verite 65 Plus - Wi-Fi Setup

English
46
Wi-Fi Setup
You can set the following Wi-Fi settings.
•
Network and Password
If you would like to connect to a Router
manually, follow the Steps below.
1 From the Control panel, navigate to [Home
> Setup > Wi-Fi Setup > Network and
Password], then press
.
Wi-Fi Setup
Network and Password
Wi-Fi Protected Setup
IP Address
Proxy
Back Select
2 Press Select the SSID that you
would like to connect, then press
.
• If it is not displayed the SSID that you
would like to connect in the list, select
[other] then press
. Enter the SSID
name, then select the security type of the
Router.
»»
Refer to “Manual SSID Setting” on page
46.
Network and Password
Router1
Router2
Router3
Router4
Back Select
3 Enter Password. Press to
select letters, numbers and symbols, then
press
.
– When you enter a wrong text character,
then you can erase it by pressing
.
– To change the characters, press
to select [a/A/1/+], then press
repeatedly until the character you
want to enter.
Network and Password
Enter Password
a b c d e f g h i j
k l m n o p q r s t
u v w x y z a/A/1/+
< > Done
4 After entering the Password, press
to select [Done], then press
.
Network and Password
XXXXXXXXXXXXX
a b c d e f g h i j
k l m n o p q r s t
u v w x y z a/A/1/+
< >
Done
5 Confirm the SSID name and Password
displayed on the Menu display, then press
. The unit will start connecting to the
Router.
Network and Password
SSID: XXXXXXX
Password:
XXXXXXXXXXXXX
Back Continue
6 [Connected to...] message will appear on
the Menu display when the connection
is successful. Press
, then the
connection setting is completed.
Network and Password
Connected to
Router1
Press
to print report.
Press to continue.
Print Continue
Manual SSID Setting
1 Enter SSID name of your Router.
Press
to select letters,
numbers and symbols, then press
.
– When you enter a wrong text character,
then you can erase it by pressing
.
– To change the characters, press
to select [a/A/1/+], then press
repeatedly until the character you
want to enter.
Network and Password
Enter SSID
a b c d e f g h i j
k l m n o p q r s t
u v w x y z a/A/1/+
< > Done
2 After entering the SSID name, press
to select [Done], then press
.
Network and Password
*****************
a b c d e f g h i j
k l m n o p q r s t
u v w x y z a/A/1/+
< >
Done
– Press to select the security
type of the Router, then press
.
Note(s)❏
• When you enter the same SSID name
manually that you previously used
on this unit, the security type is set
automatically.
Network and Password
Open
WEP-64
WEP-128
WPA/WPA2-PSK
Back Select
•
Wi-Fi Protected Setup
1
From the Control panel, navigate to [Home
> Setup > Wi-Fi Setup > Wi-Fi Protected
Setup], then press
.
Wi-Fi Setup
Network and Password
Wi-Fi Protected Setup
IP Address
Proxy
Back Select
2 Press WPS button on the Router.
Wi-Fi Protected Setup
Push WPS button
on Wi-Fi router.
120
Cancel
3 [Connected to XXXXXXXX] appears on
the Menu display, WPS (Wi-Fi Protected
Setup) is completed.
– The
XXXXXXXX
represents the SSID of
your Router.
4 Press on [Wi-Fi Setup] screen.
Wi-Fi Protected Setup
Connected to
XXXXXXXX
Next
Continued on next page.