Kramer VP-440X - Page 66

Kramer Electronics Ltd.
VP-440X – Protocol 3000
64
Function
Description
Syntax
Parameters/Attributes
Example
RESET
Reset device.
To avoid locking the
port due to a USB bug in
Windows, disconnect USB
connections immediately
after running this
command. If the port was
locked, disconnect and
reconnect the cable to
reopen the port.
COMMAND
#RESET<CR>
FEEDBACK
~nn@RESETok<CR><LF>
Reset the device:
#RESET<CR>
ROUTE
Set layer routing.
This command
replaces all other routing
commands.
COMMAND
#ROUTElayer_type,out_index,in_index<CR>
FEEDBACK
~nn@ROUTElayer_type,out_index,in_index<CR><LF>
layer_type Layer Enumeration
1 – Video+Audio
out_index – 1
in_index – Source id
1 –HDMI 1
2 – HDMI 2
3 – HDMI 3
4 – HDMI 4
5 – PC
Route video HDMI 2 to the
output:
#ROUTE1,1,2<CR>
ROUTE?
Get layer routing.
This command
replaces all other routing
commands.
COMMAND
#ROUTE?layer_type, scaler<CR>
FEEDBACK
~nn@ROUTElayer_type, out_index, in_index<CR><LF>
layer_type Layer Enumeration
1 – Video+Audio
out_index – 1
in_index – Source id
1 –HDMI 1
2 – HDMI 2
3 – HDMI 3
4 – HDMI 4
5 – PC
Get the layer routing:
#ROUTE?1,1<CR>
SCLR-AS
Set auto-sync features.
Sets the auto sync
features for the selected
scaler.
COMMAND
#SCLR-ASscaler_index, sync_speed<CR>
FEEDBACK
~nn@SCLR-ASscaler_index, sync_speed<CR><LF>
scaler_index – Scaler Number – 1
sync_speed – 0, 1 or 2
0 – off
1 – fast
2 – slow
Set auto-sync features:
#SCLR-AS1,1<CR>
SCLR-AS?
Get auto-sync features.
Gets the auto sync
features for the selected
scaler.
COMMAND
#SCLR-AS?scaler_index<CR>
FEEDBACK
~nn@SCLR-ASscaler_index, sync_speed<CR><LF>
scaler_index – Scaler Number – 1
sync_speed – 0, 1 or 2
0 – off
1 – fast
2 – slow
Get auto-sync features:
#SCLR-AS?1<CR>
SCLR-AUDIO-
DELAY
Set the scaler audio delay.
Sets the audio delay
for the selected audio
output.
COMMAND
#SCLR-AUDIO-DELAYscaler_index, delay<CR>
FEEDBACK
~nn@SCLR-AUDIO-DELAYscaler_index, delay<CR><LF>
scaler_index – Audio output
number – 1
delay –
0 – Off
1 – 40ms
2 – 110ms
3 – 150ms
Set the scaler audio delay to
40ms:
#SCLR-AUDIO-DELAY1,1<C
R>
SCLR-AUDIO-
DELAY?
Get the scaler audio delay.
Gets the audio delay
for the selected audio
output.
COMMAND
#SCLR-AUDIO-DELAY?scaler_index<CR>
FEEDBACK
~nn@SCLR-AUDIO-DELAYscaler_index, delay<CR><LF>
scaler_index – Audio output
number – 1
delay –
0 – Off
1 – 40ms
2 – 110ms
3 – 150ms
Get the scaler audio delay:
#SCLR-AUDIO-DELAY?1<CR
>
SCLR-PCAUTO
Set PC auto sync of
scaler.
Trigger the Auto Adjust
feature of PC input.
COMMAND
#SCLR-PCAUTOscaler_index, auto_scan<CR>
FEEDBACK
~nn@SCLR-PCAUTOscaler_index, auto_scan<CR><LF>
scaler_index – Scaler Number
1
auto_scan – 1 (“Yes” triggers the
Auto-scan function. When complete,
the unit returns to the “No” state)
Set PC auto sync of scaler:
#SCLR-PCAUTO1,1<CR>
SIGNAL?
Get input signal status.
COMMAND
#SIGNAL?in_index<CR>
FEEDBACK
~nn@SIGNALin_index, status<CR><LF>
in_index – Number that indicates the
specific input:
1 –HDMI 1
2 – HDMI 2
3 – HDMI 3
4 – HDMI 4
status – Signal status according to
signal validation:
0 – Off
1 – On
Get the input signal lock status
of IN 1:
#SIGNAL?1<CR>
SN?
Get device serial
number.
COMMAND
#SN?<CR>
FEEDBACK
~nn@SNserial_num<CR><LF>
serial_num – 14 decimal digits,
factory assigned
Get the device serial number:
#SN?<CR>
TEST-MODE
Perform device test
according to defined test
parameters.
This command starts
device test procedure.
COMMAND
#TEST-MODE<CR>
FEEDBACK
~nn@TEST-MODEresult<CR><LF>
result – Test Results
0 – OK
1 – Failed (general)
2 to N – Device specific failed error
code
Perform device test according
to defined test parameters:
#TEST-MODE<CR>
TLK
Set audio talkover mode
status.
COMMAND
#TLKio_index, talkover_mode<CR>
FEEDBACK
~nn@TLKio_index, talkover_mode<CR><LF>
io_index – 1
talkover_mode – Talkover mode
0 – Off
1 – Mixer
2 – Talkover
3 – Mic only
Set audio talkover mode to
Mixer:
#TLK1,1<CR>
TLK?
Get audio talkover mode
status.
COMMAND
#TLK?io_index<CR>
FEEDBACK
~nn@TLKio_index, talkover_mode<CR><LF>
io_index – 1
talkover_mode – Talkover mode
0 – Off
1 – Mixer
2 – Talkover
3 – Mic only
Get audio talkover mode status:
#TLK?1<CR>